(800) 853-2651
SHOP NOW

Search results

  1. T

    New fuel pump problem DK40

    Bought a new pump and went to install. The new pump has a part that sticks into the engine is not machined, it is just a casting and is too fat to fit in the hole on the engine. The original pump was machined in this area. The casting is about .020 too big to fit. I looked other replacement...
  2. T

    Kioti DK40 fuel gone/

    wENT TO START MY dk40 this spring and the tank was empty. poured in 5 gal diesel then 15min later tried to start, almost started then stalled. checked the fuel and it was empty again. Checked the oil level and found the fuel. I guess the pump is bad. Has this been a problem?
  3. T

    1951 8N hard first start

    My 8N does not start cold unless I cover the intake with my hand. The choke works fine and after it starts it runs good. I put another carb on off my other 8N and it starts just fine. I have gone through the carb, cleaned it out, blew it out, adjusted float level and it still will only start...
  4. T

    generator mount 52 8N

    trying to put the gen on my 52 8n. it has the left side gen. if I put the strap mount on with the engine side ears in front of the tractor mount the gen is too far forward, pulley does not line up. if I put I put the ears too the rear the adjuster hits the block, but the pulleys line up. I...
  5. T

    shift boot

    just bought a new shift boot for my 51 8n from DC and it is way too small to go on to my trans cover. they list 1 boot to fit all 9,2,8 N tractors, are they all the same? is there an other brand that fits, like Massey or JD ?
  6. T

    masking hood and fender script

    I am painting my 51 8N and have seen masks for the script on the fenders and hood. Has anybody used them and is 1 brand better that another? Would you use them and how do they work?
  7. T

    rear rim bolts

    The replacement rim that I bought for my 8n has sort of round loops for the mounting and the other rim that was on the tractor has square loops that uses the original type bolts. What should I use on the replacement rims with the round loops? The square on the original type bolts is too big to...
  8. T

    51 8n lt axle housing

    I pulled the left axle housing on my 51 ford 8n to replace the lower pivot pin. Now I am trying to reassemble it. I pulled the whole assembly as 1 piece. Now it will not go back in, the inner axle end does not go the last 2 inches. What am I doing wrong? Any secrets to align it?
  9. T

    lower lift arm

    The lower lift arm bolt on the trumpet on the left side of my 51 8n is loose and just spins trying to tighten it up. It also leaks at the bolt. What does it take to fix this.
  10. T

    proofmeter cable

    how do I disconnect the cable from the governor on my 8n? what looks like a nut on the end of the cable just keeps turning with the whole cable.
  11. T

    brake drum screws

    trying to remove the 2 screws that hold on the brake drum on my new (to me) 8N. After trying the impact drive with no luck I used the old trick I used on other screws. I used the oxy torch with a small tip, heated the screw up till it was red hot then let cool. The screws came out with a...
  12. T

    8N running board

    I just bought an 51 8n, the left running board is different than my 48 8n. The left board has a different pattern, not the diamond pattern of the 48, the 51 has more like dots and it also has a molded in slot along the side next to the tractor. It seems to fit like the 48 style. What does...
  13. T

    48 8n rear axle seal bolt

    I am replacing the brakes and seals on my 48 8n. The last person when they replaced the outer seal must have lost the bolts that hold the seal holder, the ones that press into the seal holder. I want to get new ones and can not find a listing. Where do I go or do I have to use regular bolts...
  14. T

    48 8n rear axle lock nut removal

    I want to remove the rear wheel hub on my 8n and the left side has what I think is a locking nut. When I look up this nut it shows an inner nut and a outer nut with some kind of lock tab. HOW DOES THIS COME APART? The right side has the standard nut and lockwire. I am guessing the left hub...
  15. T

    MH50 snowplow

    The MH50 that I bought came with a MF10 snowplow. The plow has a id plate on it and says it is a MF10. It has long push arms that look like they go back to the rear axles and cables that must be to lift somehow. Does anybody have any information on this plow, how to hook it up or parts list?
  16. T

    urethane paint repair

    I painted my 8N ford with urethane paint and when I rubbed it out I burned through on the ribs on one side of the hood. Is there a way to repair, blend in, the paint on that side or do I have to repaint the hood? Thanks
  17. T

    EI voltage in 8N

    I am installing a electronic ignition in my 8N and need to know if the original resistor should be bypassed. Originally it lowered the voltage as the tractor warmed up. But I think that the electronic needs the full voltage all the time. There does not seem to be any mention of it in the...
  18. T

    Ford 8N medium gray

    I am looking for a modern urethane paint to match the medium gray paint on my 48 8n. The only paint that I can find is Tisco tp240 or Sparex tp240 and both of these are old style synthetic enamel. I have found a modern paint for the red. I would like the newer acrylic urethane paints that...
  19. T

    starter solenoid

    Changing my 48 8N over to 12v. Do I have to change the starter solenoid to a 12v style? The starter will be OK on 12v. I am using a solid state ignition. What type plug wires do I need? Thanks
  20. T

    MF-65 paint color

    I'm painting the MF65, sheet metal M-1041 red, engine and chassis M-1025 metallic flint gray, rear rims M-1037 silver mist. What color do I paint the grill mesh, rear wheel discs,and ft wheels? Any other colors used on other parts?
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top