(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. A

    WD9 cross shaft return spring - 52 176 DC

    Thank you so much! I had done a good bit of searching, and had just about settled on a substitutes generic spring.
  2. A

    WD9 cross shaft return spring - 52 176 DC

    Got my magneto insalled and coarsely timed, and the big spring that hooks on behind the carb broke when I bumped it. Since it controls pretty much everything, I didn't try starting the tractor til I can hunt one down. I lookd through the parts book and service manual and can find no specs...
  3. A

    Looking for gas-start magneto for WD-9

    Yeah, was looking at service manual, and they don't show the rotor except in a "keeper" outside the unit. I looked at the larts book and it is just the shaft, so i guess the magnets are there. The impulse doesn't appear to be catching either. I've replace points and condense before, but...
  4. A

    Looking for gas-start magneto for WD-9

    Yes, shiuld have mentioned that Inhave a couple of the clockwise mags. I had a 39 H that I ran for several years with no battery or starter.
  5. A

    Looking for gas-start magneto for WD-9

    Got my WD-9 in from ND, and I've been cleaning up the fuel system. Finally got clean gas to the carb, and no spark. Some PO had wire in an external coil. I wasn't getting fire, so I ordered a new coil, points, condense, rotor, and cap. Welll, when I opened her up ther was no coil in the...
  6. A

    WD9 flooding.

    https://www.mcdonaldcarb.com/product_p/mcd-32581dxb.htm
  7. A

    8n Gear

    If it was my tractor I would probably put off opening it up til I had to take it down til I had timebto take it apart and relly check it out. If you can see the gear, maybe look around for a goo one to replace it. I about to have to rebuild my late FIL's 3N, and it needs a full set of...
  8. A

    Gas start diesel run engines

    When you say "cold weld", what do you mean? Is this taking a punch and peening the cast iron together in kindnof a knitting operation, or some other orocess?
  9. A

    You guys that haul regular, what?s your thoughts on thiis?

    Have a similar rig from kearny. You only have about 9500 # of payload. I have hauled a 2n and a JD 60 at the same time and had a balance load, and pulled with a 2015 6.7 F250 with no probkems. Kept it to 60, and had nonissues.
  10. A

    Ford 6.7 diesel

    Very early 6.7s had a problem with valve stems sticking from overheating when they went into regen mode. Unless this one has been fixed, that is likely the problem. Can get complete engine failure if it sticks and the piston contacts it.
  11. A

    Road gear for Unstyled B

    Pretty much all the tractor rides around here have a 10mph minimum.
  12. A

    It will not even pop!!!!

    Clean the plugs. 8)
  13. A

    2 Cylinder JD PTO - Worthless??????

    I have used my 420 to mow with a 3pt RM59 woods finish mower a good bit. The PTO is offset a bit to the left,but there is almost always as much or more vertical offset than there is horizontal offset, so I never worried. The woods is belt drive, and has a VERY heavy drive line. Never an...
  14. A

    Were the gas start diesels harder to crank?

    And another note on timing: As far as I know, ALL of the gas start diesels were magneto ignition. I don't know if they were ever offered with battery ignition. I will not even attempt to crank start a battery ignition, or a magneto I have not verified the timing on. I've seen too many vacuum...
  15. A

    jd 420 lp

    ALWAYS, turn the gas off and let the motor die, THEN turn off the ignition. If you turn the key off first, you still have HOT water in the vaporizer/regulator with the liquid fuel. This will build up high pressure, and badly abuse the gaskets in the vaporizer. By the book, you start it on...
  16. A

    Farmall B parts on an A

    What is involved in switching an A to a Narrow Front? Is it simply removing the wide front and bolting on the B pedestal for the front wheels? I have a line on a cheap A, and want to make another mowing tractor out of it. I have a Woods L306 belly mower that will fit. Thanks, Alan
  17. A

    Woods Mower

    Woods will sell you everything you need. It will be a bit pricey. Or you could haunt Craigslist or Ebay. Some of what you have may be usable.
  18. A

    rebuilding the hand crank-F20

    Forgot to mention on mine, the mag trips at 12:00 and 6:00. I have it time to fire 1-2 degrees ATDC. It actually has more compression now than it did right after my surgery last year. I worked it about 3 hours at WOT fully loaded with a 6' mower and compression was NOTICABLY better afterwards...
  19. A

    Super A rotary mower question

    You could rig a couple of lift arm eyes to clamp to the drawbar, and just drag one of the rear 3pt finish mowers that run on 4 casters. Seen that done quite a bit, and was about to do that to my H til I found an L306 Woods to fit it.
  20. A

    rebuilding the hand crank-F20

    Actually, my '39 H has the same issue, to a lesser degree. I don't know whether it is because I am weak, or short, or both. I could never get enough momentum on the upstroke to let it coast past TDC. I'm right-handed, so I stand to the left of the crank facing the tractor, as you should, and...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top