Search results

  1. B

    706 fast hitch leveling yoke

    I broke one of the leveling yokes on my 706(don't ask how it's a long story :roll: ). Is there any trick to getting the threaded part out of the yoke ? Thanks for the help! Brian
  2. B

    Back on YT!!

    I'm going to be back on again occasionally as I finally got a new computer after my previous one blew the hard drive. Also had a lot of back problems as well. :D
  3. B

    Back on YT!!

    I'm going to be back on again occasionally as I finally got a new computer after my previous one blew the hard drive. Also had a lot of back problems as well. :D
  4. B

    Back on YT!!

    I'm going to be back on again occasionally as I finally got a new computer after my previous one blew the hard drive. Also had a lot of back problems as well. :D
  5. B

    Winter project

    Got a project for winter, have to pull the head on my uncle's WD9(he bought it new, ordered it while he was in the army and it was waiting for him at the local dealer when he got out at the end of the WWII). Warped starting valve. This will be first time head is off since he overhauled it in...
  6. B

    WD9 valve cover gasket

    Does anyone know where I can get a valve cover gasket for a WD9 at or maybe some cork material to make one? I checked Stieners and their cork pieces they have in the catalog are too short to make one. Thanks, Brian
  7. B

    881 FINISHED

    Finally finished repairs on the 881 today by installing a rest-o-ride seat! So nice to have a seat with suspension on it! Did a lot of work on it but she's been kind of neglected for a lot of years. Thanks to LarryNCKS and JiminNM for the parts and seat. Brian
  8. B

    881 getting closer to finished

    This one isn't even a restoration, just some long overdue maintenance. Hope everything goes well with your back surgery. I'm suppose to have 1-5 lumbars fused but I'm not doing it till absolutely necessary. Actually that part of my back bothers the least. The upper part of my back has...
  9. B

    881 getting closer to finished

    Got the fenders and loader frames back on yesterday. Worked on getting the red tail light and rear work light functioning( I think that's the first time the tail light has been on since 1960). Putting her on the dyno tomorrow for a bit and give the bands a final adjustment. Next week the...
  10. B

    881 D fuel tank

    Tank is back on, NO LEAKS(so far). Had it running today for a bit, adjusted the brakes, packed wheel bearings. Going to try and get fenders and loader brackets back on Thursday. Going to work it on the dyno Saturday and then re-check trans bands. Brian
  11. B

    Rest o ride seat

    Sent you a email Jim. Brian
  12. B

    881 D fuel tank

    Got the tank back today. The guy couldn't believe it was leaking worse than before he fixed it. He then said he thought he pressure tested it, but wasn't sure if the air was on in his testing hose......Guess it was a senior brain fart moment. lol Brian
  13. B

    Rest o ride seat

    My cousin is kind of looking for a rest-o-ride seat to put back on the 881. I know they're darned expensive to refurbish. Just throwing it out there if anybody has one in ok shape and reasonably priced? Thanks, Brian
  14. B

    An SOS I Can't Figure Out

    Good one Larry! Now I have a serious one for you. Where can I get a water pump for a '63 Chevy Corvair? lol Brian
  15. B

    881 D fuel tank

    Hi Larry, My o-ring kit is resistant. Tank is leaking where it was cracked and repaired. So the guy has to do it again. Hopefully he gets it this time! Brian
  16. B

    An SOS I Can't Figure Out

    Maybe a o-ring out on a servo piston or broken servo? Just guessing. Brian
  17. B

    881 D fuel tank

    Put tank on and put fuel in and tank is leaking worse than before it was fixed. :evil: Took it back off and hopefully have it back this week. Going to put some fuel in it before I put back on this time!!! Brian
  18. B

    881 D fuel tank

    Fuel tank is fixed, but I need to replace the o-ring that goes on the shutoff valve and tank. I know I've seen messages showing the dimensions of the o-ring. Can someone give me the size? Thanks, Brian
  19. B

    Something different

    Thanks Wayne! Prices look reasonable from Bradish as well. Brian
  20. B

    Something different

    My cousin would like to know the cost of a complete decal set for a 881 diesel. I checked on YT and I see they have the two for on the side of the hood, but is the other set for the other models include all the other decals needed(including the diesel decals for the hood)? I know there...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top