(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. L

    Two bottom plow

    I had the same problem I used Kubota with bucket and chain or straps to load in two wheel trailer. I would not try to put in truck bed to avoid damage to truck. Trailer is best.
  2. L

    John Deere 415

    Thank you for helping with advice.
  3. L

    John Deere 415

  4. L

    John Deere 415

    I need help in what to do about a brace 31754A and special bolt A11575A 5/8 X 3 1/4 inches. My brace is bent in a U shape which a machine shop may straighten but I need to buy a new bolt. All parts information is obsolete. I sandblasted,repainted & replaced everything else. All I need is the...
  5. L

    John Deere plow

    I have a John Deere 415A two bottom plow original. I have removed all plow points and ready to have sand blast and repaint to original color. Plows in my area are selling for $200 to $250 and all plow points are costing me over $300. I hate to scrap this plow and would welcome advice on it...
  6. L

    801 ford carbureator rebuild

    I appreciate your reply but I rather rebuild than buy it needed.
  7. L

    801 ford carbureator rebuild

    I would like to contact Royse. If I could get his email or Royce contact me at [email protected] I would appreciate it.
  8. L

    801 ford carbureator rebuild

    I need someone to rebuild my carb. There was a post months ago about a man in Alabama that rebuilds to perfection. If anyone can remember who he is or how to contact him I will be grateful.
  9. L

    801 ford carbureator rebuild

    I have a carburetor that stays wet when motor is running. I would like to have someone rebuild it for me. There was a post about a man in Alabama that rebuilds to perfection. I will search in the archives but if anyone can remember that man and any contact information I will be...
  10. L

    disk axles

    I bought a Linebaugh disk with 18 inch scalloped disks. The disks are in good shape. I need to replace the bearings. The disk has round axles 1 1/8 inches. The disks spacers and bearing cups have square holes. Should I use the round axle or try the square axle. I appreciate your advice and help.
  11. L

    oil bath

    My uncle used to line breather of old ford cars with KOTEX and I would like to know if that would work on my 801 Ford in place of oil?
  12. L

    body work

    Thank you ROYSE for replying and you saved me a lot of time and some money.
  13. L

    need help with body

    I started to put one side of body on and noticed I misplaced connection from frame to body (dogleg). Below the radiator are two square cut outs that are 3/4 X 1/2 inch. The correct part according to parts manual is lower plate assembly RH NCB-88074 and LH NCB-88075 5/16--18. I found part in...
  14. L

    Helpful fellows

    I wish I had some of the knowledge Destroked 450 and the other fellows have. I look at the forums often for any information on 600 and 800 tractors. By the way I am using a 6 volt solenoid with one post for the starter switch. THANKS TO ALL OF YOU!
  15. L

    FORD 800 FORD 801 Serial numbers

    I would like to get the correct model of my tractor. Destroked 450 said his dad had a 800 ford. I ordered a Guage set and that is why it has a amp Guage. My serial number is 20886 Model 851-L. It is a gas model and I have reworked most of it with over $900.00 worth of parts from yesterday...
  16. L

    801 electrical system

    My 801 has 6 volt solenoid. The starter switch by the gear shift only works with one connection on 6 volt solenoid. Tried solenoid with two connections and it does not work. Will the NAPPA IC14SB coil WORK WITH 6 VOLT SOSOLENOID. Thanks for previous reply.
  17. L

    ford 801

    I wired my ford 801 with new wire harness. Wire from coil positive to resistor and resistor to amp guage the tractor will not start but if alligator clips are put on each side of resistor it starts perfectly. What am I doing wrong? 12 volt conversion.
  18. L

    oil for ford 801 gas

    I was reading a forum about changing oil where they used 10 W 30. The mechanic that is helping me said to use 15 W 40. Before I buy the oil I would like to hear from someone from this forum. I am concerned about oil pressure and line to oil pressure guage. I will be looking for your advice.
  19. L

    ford 850 unknown part.

    THANKS ROYCE. Is this a radiator drain or a block drain. I am unsure of the thread. Also I said painting motor and frame. I should have said motor-transmission-hydraulics- rear end-lifts but I thought frame covered about every thing. Thanks INFORD. THANKS AGAIN FOR THE BEST HELP AVAILABLE AND...
  20. L

    ford 850 unknown part.

    THANKS! Part is not a freeze plug. It looks like a small plug or something that has been broken off. Picture in ford tractor master parts catalog that looks like radiator drain plug with no identification or part name.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top