(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. B

    3020D 24V Starter

    Thanks Jim, I'll do some more poking for the short;
  2. B

    3020D 24V Starter

    I don't know. The wiring diagram that I have for a 3020 diesel only shows a single regulator. Tx Jim: what causes the solenoid to stick with low batteries? Does it chatter and then basically welds itself because it's arcing over rather than making a fast, clean, connection? J
  3. B

    3020D 24V Starter

    I didn't know for sure until I did some searching. The wiring diagram that I have for a 3020 diesel only shows a single regulator, however, it appears at some point there was an updated loom for the 3020 that added a second regulator. I don't have that diagram though; maybe someone else does...
  4. B

    3020D 24V Starter

    Hmmm. There are two regulators. I think the brown wire from the loom goes to the small terminal on the back of the solenoid (inner). I had it on the S terminal where the safety switches end. J
  5. B

    3020D 24V Starter

    Thanks, Jim. Right battery is 12.95 left battery is 13 volts. I tested hooking the solenoid and starter upb the way it would be on the tractor and then firing the solenoid and it all seems okay. If I hook negative up to the negative post on the solenoid and I hook positive up to the positive...
  6. B

    3020D 24V Starter

    Hi All! My 3020 Diesel needed a starter. I was able to get a reman locally from a reputable source and I have the following symptoms that I'm puzzled by. I got the starter put on, wired up, and connected R and L batteries back up and fired it up. Starter worked great; tractor fired right...
  7. B

    Case 480C Forward/Reverse loss and Clutch Disconnect

    Hi! I have a new to me 480C with what I think is maybe an electrical problem but I've never had one before and so I don't have a lot of experience troubleshooting them. I have 2 problems, but they may be related so I'm sharing them both for somebody who has more experience than I do. 1)...
  8. B

    550 PTO Shaft

    I've looked pretty long at it. The shear happened along a crack that appears to have started in the hole in the stub shaft for the retention bolt. It had been that way for a while because there was a hint of rust along the crack, which tells me it had been weakened in the past. I think the...
  9. B

    550 PTO Shaft

    Hi folks! I have a project that's been staring at me all summer..and now that my employment status has changed, I have a bit of time to dig in and I'm looking for advice/ideas. I've got a 550 where the PTO stub shaft sheared off this spring. I've pulled the retaining bolt and tried a lot...
  10. B

    Oliver wire terminals

    Aha! I found what they are: GM56.
  11. B

    550 Clutch Safety Switch

    Awesome. Thank you! I haven't pulled the instrument cluster on mine, but, I need to replace the key, light, and fuel/temp gauge. I suspect mine is disconnected and that is what I will find when I have the dash apart. Wife or daughter may drive this one.. so want to get that switch sorted out...
  12. B

    Oliver wire terminals

    aha! That is who i saw the shot from! Thank you!
  13. B

    Oliver wire terminals

    Hi, I don't know if these are unique to Olivers.. I have an 1850D that I'm rebuilding the wiring harness for; I had thought I'd just have to re-use the old terminals (there that slide onto the keyswitch).. but I saw a still shot from a video the other day and the guy appeared to have new...
  14. B

    550 Clutch Safety Switch

    Is it threaded into the clutch pivot into the hole at the end there?
  15. B

    550 Clutch Safety Switch

    Hey again folks! I'm looking for some photos or a good description of the safety switch setup. Looking at my 550, I appear to have the switch, but, it's probably been defeated as I don't see any way it could be actuated. Looking at the parts book, it appears there should be a rod...
  16. B

    550 front PTO lever

    Hehe..I will take your optimism!
  17. B

    550 front PTO lever

    Looking at mine, it is also missing the spring and I was looking; appears to me if you knock the roll pin out of the latch, you should be able to pull the button out and re-spring it; though maybe that rod tha actuates the latch threads into the base of the button.. which means it's probably...
  18. B

    550 front PTO lever

    Ahhhhhh. I was lookin at the image of the rear lever and not drawing the conclusion that the other one was the front mounted. After looking at that; i think I'm only missing the spring, and, the part that bolts onto the tractor that it latches to; think I can make that easily enough. I spent...
  19. B

    550 front PTO lever

    550 Front PTO lever Does anyone have photos of one of these on a tractor? The partsbook online doesn't let me get my head around how this should look. Parts are missing for sure. I just picked up a 550 and i think the PTO engagement lever is in front, ahead of my right knee. It's missing...
  20. B

    1850D Tachometer Drive

    Thanks Jack, Comparing to my 2-105, the aux-drive block appears different. At this point I think I have the right-angle adapter filed to where it will work. An 80 speedo cable is proper length, but, the driven end is the wrong configuration for whatever was meant to engage in the...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top