(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. G

    Leyland 2100

    Thanks derwen
  2. G

    Leyland 2100

    Hi, I am restoring a leyland 2100 tractor & am finding it difficult to source rear tyres & rims for it in the uk (15.30x34), does anyone know if any other tractor tyres/rims may fit it perhaps from a nuffield or some other, at the moment it has rowcrop wheels on it. Thanks for any advice you...
  3. G

    I.H 784

    hanks it will be a great help, as there are lots of other parts we will require
  4. G

    I.H 784

    Hi I have had a look but cannot see any I.D number on the casings would you or someone post a photo of this number & the area so I may get a better idea where it should be if possible the only number I have found is on the block which is '96' which doesn't mean anything to me.
  5. G

    I.H 784

    hanks IH Timmy will have Look
  6. G

    I.H 784

    Hi I'm having a problem finding the engine model number on my 784 I believe it begins with a letter followed by three numbers its an 84 series does anyone know where to locate it I need it to find replacement parts for the engine rebuild I believe. Thanks
  7. G

    Crankshaft bearings

    That's about right, "spinning" as you say, suppose "dislodged" was the wrong word, Anyway now waiting for the right equipment to be delivered then see how we get on. Thanks for all your replies & will keep you informed with the outcome.
  8. G

    Crankshaft bearings

    Hi, it became dislodged due to ware & tear I presume, it was quite scored, the crank itself doesn't appear to have any marks on it but maybe worn I suppose, I haven't tried plastigauge or a micrometer so I will do that, didn't know there were 3 different standard sizes of bearings, I just...
  9. G

    Crankshaft bearings

    i, Sorry for any delay in getting back to the subject it must be a time thing as I am in the UK, as I said when dropping off the sump found the rear c/shaft bearing dislodged & badly scored & was unable to read the serial number for the replacement part so had to remove another one to...
  10. G

    Crankshaft bearings

    hi, going back to the beginning the engine started knocking after a few minutes as it was warming up,( had the same trouble with a ford) after a couple of times it wouldn't turn over like the engine had ceased, dropped the sump off to try to see what might have gone wrong from underneath &amp...
  11. G

    I.H 784 won't start

    i Shaler thanks for your reply, the battery is new today cca is 800 & the terminals are clamp on not sure what gauge though, tractor is tucked up in the barn for the night freezing cold with snow & strong winds don't think I will be venturing out there anymore until tomorrow!!!, will...
  12. G

    I.H 784 won't start

    Hi all, have a problem starting, have already posted about this on the crankshaft bearings problem thread but thought I should start a new thread, after sorting out the bearing problem, it seemed to be a new starter motor needed,so replaced it, but the engine only turned over slowly a few times...
  13. G

    Crankshaft bearings

    i all, thanks for all your replys , the crankshaft now sorted not quite sure what the problem was but it turns over now but the problem doesn't end there!!!, turns over slowly but seems the battery runs down after two or three turns!!!, replaced the starter motor same thing happens, replaced the...
  14. G

    Crankshaft bearings

    Hi, I have a problem fitting a crankshaft bearing in my I.H 784 tractor, when I fit the new bearing & tighten it to the specified torque the engine will not turn, I put the old one back on & it does the same, the crankshaft can be turned by hand when the bearing is taken off, can't see...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top