(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. T

    Power steering fluid pumping out the steering column on Ferguson MF35 Diesel

    Stan, thanks for the replay, My steering shaft is in fair condition, a little pitting but only seen through a magnifying glass. I still applied marine grade JB weld to it and sanded it down to make seal, but it still isn't staying sealed when the fluid gets hot. I can work the tractor for...
  2. T

    Power steering fluid pumping out the steering column on Ferguson MF35 Diesel

    Thank you for the response. I have heard of the sleeves and will look in to them. The other option would be to buy an aftermarket steer box so I think I will try the sleeve. Can you tell me if the sleeve you used had a flange on one end or was it just a cylinder sleeve? What keeps it tight...
  3. T

    Power steering fluid pumping out the steering column on Ferguson MF35 Diesel

    On my Ferguson MF35 Disel , after running for about an hour it blows all the steering fluid up through the steering column. I have replaced the upper seal and o ring in the column, but it still blows out after running for about an hour--after it gets hot. As the fluid is pumping out through the...
  4. T

    I am repairing a MF 35 PTO.

    Thanks Harry, yes if the groove in the rockshaft cam doesn't matter, I won't mess with it. I am concerned about getting it smooth and level anyway for the roller....and I found the specs on the adjustments so I'll see if I can make heads or tails of it and I will do what you said and watch the...
  5. T

    I am repairing a MF 35 PTO.

    Thanks Harry, yes if the groove in the rockshaft cam doesn't matter, I won't mess with it. I am concerned about getting it smooth and level anyway for the roller....and I found the specs on the adjustments so I'll see if I can make heads or tails of it and I will do what you said and watch the...
  6. T

    I am repairing a MF 35 PTO.

    Thanks Hobo, I was able to find the book on the MF35 from the web site. Thanks so much, it does describe the adjustments, so I will have to read a few times to understand it, but so good to have. I might try to weld in a fill to the worn groove on the rockshaft cam, but if it doesn't matter I...
  7. T

    I am repairing a MF 35 PTO.

    Thanks Harry, do you know where I can find the adjustment specs for the position and draft control before I put the lift cover back on? I purchased a used complete head unit complete with lift arms, piston, controls and quadrant. The question I have is I see the rockshaft lobe has a groove...
  8. T

    I am repairing a MF 35 PTO.

    Harry, I have a picture of my pressure relief valve. How can I tell if it is a 2500psi or 2000psi? How can I tell what I have? MF35X Ferguson Attachments MF35 press valve.jpg 2.7 MB · Views: 9 MF35 press valve end.jpg 2 MB · Views: 9
  9. T

    I am repairing a MF 35 PTO.

    I have a picture of my pressure relief valve. Can anyone tell if it is a 2500psi or 2000psi? How can I tell what I have?
  10. T

    I am repairing a MF 35 PTO.

    1. Looking for information on replacing my hydraulic lift head cover. Casting number is 184 384 M2-- I think the Ferguson part number is 190861M2 ?? Those are hard for me to find but I also saw that there might be a heavy duty version that takes the place of that part number. It is...
  11. T

    I am repairing a MF 35 PTO.

    Yes, everything looks tight and in place other than the cover. My hunch is the jam shocked the pressure/list piston and the pressure valve didn't release and it pushed the ram bolt (piston arm) back into the cylinder housing crooked which pushed down on the cylinder housing, breaking the rear...
  12. T

    I am repairing a MF 35 PTO.

    Thank you, I will replace the releif valve for sure. I hear there is an upgraded valve that is designed for the new diff/trans oils of today that are lighter. The original oil for Ferguson was a mineral type oil, but I think my issue came from a stuck valve or an out of adjustment draft or...
  13. T

    I am repairing a MF 35 PTO.

    Thank you for the response. I think my pump doesn't have a filter either. I will definitely consider a new pump with a filter as I reassemble.
  14. T

    I am repairing a MF 35 PTO.

    I took the lift cover off. No visible internal damage except the broken hydraulic lift cover. It also broke the back two bolts off the lift piston cylinder housing too and lifted the front section of the cover. Has anyone seen this damage before without damage inside the case? I'm thinking it...
  15. T

    I am repairing a MF 35 PTO.

    I will be taking it apart this week . I will update when I find out what happened in there. I was wondering if anyone had this happen and what it ended up being for them. I think there is a pump fastened to the underside of the lift cover? I have heard a pressure relief valve could also stick...
  16. T

    I am repairing a MF 35 PTO.

    I am repairing a MF 35 PTO. The hydraulic lift cover broke when something snapped inside while mowing. It broke over the small cover plate closest to the shifter. I am trying to order a new Hydraulic lift cover. The number on the cover is 184 384 M2. I think that is the heavy duty version...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top