(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. Ivor

    Yanmar YM2010 clutch

    Hey Thank you for your replys . The tractor works great i didn't need to adjust the clutch seems to work fine . Thanks so much for all the help couldn't have done it without your help . Sorry if i messed you around a bit if there a next time i try to be a bit specific. I will look for a manual ...
  2. Ivor

    Yanmar YM2010 clutch

    Hey Ok so i got it moving on the shaft alright and have put it on and put the tractor back together but i forgot to how to adjust it . Do i need to split it again to adjust it ? and how do i adjust it Thanks Toby
  3. Ivor

    Yanmar YM2010 clutch

    Hey Sorry i keep getting mixed up with the names and parts . So i wire brushed it and sanded in between and on the splines . The input shaft of the transmission comes off (in the photo ) does that mean i don't need a tool to aligne it ? I managed to get the new one on with a bit of wood and a...
  4. Ivor

    Yanmar YM2010 clutch

    Hey Thanks for your instructions i'll do that when it's together . What sort of epoxy should i get ? I just got the old clutch plate off the rod and going to put the new one on but do i have to force it on or does it just go on easily ?i had to grind off the old one . The spikes on the rod...
  5. Ivor

    Yanmar YM2010 clutch

  6. Ivor

    Yanmar YM2010 clutch

    Ok . Another problem has come up . There is a crack along the engine block it doesn't go from end to end yet and it's leaking water . Would it be alright if we put stuff to seal hole in to the water ? Thanks Toby
  7. Ivor

    Yanmar YM2010 clutch

    Hey can i resurface it with a grinder ?
  8. Ivor

    Yanmar YM2010 clutch

    we use it to cut hay and topping every year so quit hard . but it was easy to split. ok i'll just wire brush it so all the rust is off and put it back together and hope for the best . Thanks for your reply Toby
  9. Ivor

    Yanmar YM2010 clutch

    Hey Sorry for the wait . Here a photo of the broken clutch . One more thing . after cleaning the bits off the flywheel from the disc there are little rust holes where the disc went , can i still use it ? here a photo to Thanks Toby
  10. Ivor

    Yanmar YM2010 clutch

    Hey we have split the tractor successfully and taken the clutch off . It was the clutch because the metal pressure plates were broken . Thanks for all the help and advice , it's really really appreciated . Toby
  11. Ivor

    Yanmar YM2010 clutch

    Sorry here the photo
  12. Ivor

    Yanmar YM2010 clutch

    Hey Sorry for the late reply . been really busy . Thanks for your reply and diagram .sorry i should have looked at it properly . i have taken the tractor apart and looked in at the linkage the diagram extactly right thanks .here a photo of it without the cover on What do you guys think ...
  13. Ivor

    Yanmar YM2010 clutch

    hey thanks for advice . which side is best to roll away ? the front or the back ? i was going to roll the front forward but don't want it tipping . How would i wedge the front wheels ? Thanks Toby
  14. Ivor

    Yanmar YM2010 clutch

    Hey This is a new clutch ; https://mtparts.fr/winkel/japanse-tractor-parts/yanmar/clutch-kits-yanmar/kit-dembrayage-yanmar-type-4/ Thanks Toby
  15. Ivor

    Yanmar YM2010 clutch

    Hey thanks for your reply .I'll look into spliting it then. Could it be that there's not oil in the chamber ? Thanks Toby
  16. Ivor

    Yanmar YM2010 clutch

    Hey guys We started our tractor the other day and it went right to the floor and won't change gears . We are going to get a new clutch but i wanted to make sure that it was that . And also how would we split it without any special tools ? Thanks Toby
  17. Ivor

    Choosing case ih sickle bar mower rockguards

    Hey thanks for your reply . I think you sent me that but i couldn't find it . it's like bent in some different places as well i could send a photo tomorrow . I haven't got a loader or anything and wouldn't it bend too much if i drove on it ? could i clamp it to a flat bar and like heat it up or...
  18. Ivor

    Choosing case ih sickle bar mower rockguards

    Hey guys sorry for late reply . Thanks for all the advice it's really appreciated. I have put on all the rrockguards and got them mostly even and have raised the ledger plates but the bar is bent like an arc so i am trying to figure out how to bend in back . What would you guys advise? i have...
  19. Ivor

    ride on mower not sucking fuel from the carb

    Hey Sorry i was rushing .i'll try to be more specific in the futur if i do more posts. Anyway thanks guys for the help . Toby
  20. Ivor

    ride on mower not sucking fuel from the carb

    Hey Thanks for help really appreciated. Ifound out what it was ; because i took the engine apart i messed u[p the valve distance a bit .it runs alright but want to make sure . the engine is tecumseh 16.5 hp ohv . Thanks again Toby
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top