(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. F

    NH 489 roll bearing removal.

    I did find the set screws; my fingers and eyesight must be getting bad! It looks exactly like Jim.me posted a pic of. Now the fun part, the set screw is not budging, so I'm soaking in with PB blaster, then I will try some heat just with my propane torch. Thank you for everyone's advice.
  2. F

    NH 489 roll bearing removal.

    Thank you.
  3. F

    NH 489 roll bearing removal.

    On the 2 489s I have I only see 1 hole, At first I thought maybe a drift pin was in there, but only found 1 hole and no set screw, I will look at it more tomorrow, thank you.
  4. F

    NH 489 roll bearing removal.

    No. I so far just tried to see if a set screw was in there, I will try that tomorrow.
  5. F

    NH 489 roll bearing removal.

    Can anyone give me some advice on how to get the lower right side roll bearing out on a 489 Haybine? The service manual isent much help, what I see is a lock collar on the end of the roll shaft to hold the bearing assembly in, there is a hole in the collar, but no set screw, which leads me to...
  6. F

    What tractors did you drive as a kids?

    Ford 4600 with Dunham Lehr loader.
  7. F

    Repair or service manuals.

    what if I need a torque spec? or how much fluid is needed? ect? I don't expect much input from a simpleton who farms with junk!
  8. F

    Repair or service manuals.

    Ford truck manuals for my 2000 F250 and my Ford tractor manuals, it doesn't say who published them.
  9. F

    DIY A/C Repair

    Id say do it your self, i replaced the condenser, and compressor on my 2000 F250, and recharged it myself, and it works fine now, the only thing I haven't replaced is the evaporator behind the glove box. I hope I do not have to because it looks like a big job.
  10. F

    Repair or service manuals.

    Can anyone explain why service manuals are not like a book with normal chapters, why do they have chapters, with sections and the same page numbers threw out the manual. Normally chapter one is fuel system, pages 1 threw 20, chapter 2 engine, pages 20 threw 60, like a normal book, but most...
  11. F

    Ford 4600 3 pt category change

    Somebody must have changed the lift arm or the end, the end on the right of your hitch doesn't even have the casting for the spring retainer. Id go to a tractor salvage yard and see if you can find the end or the whole arm, if you live near a salvage yard, or look online, maybe All states ag, ect.
  12. F

    Mower deck leaves winrow

    That is perfectly normal for a brush hog mower, I have a woods M5, and a 6foot Howse, both do the same thing, that's how they discharge the cut material.
  13. F

    Ford F-250 gas engines

    My buddy has a 2015 with a 6.2, only 40,000 on it, but he likes it so far, it is a 16 spark plug engine, and otherwise a little hard to work on. The way he drives I think he gets 10 mpg.
  14. F

    Bat wing mower

    Thank you for the pics and replies everyone, I agree, a 12" would be my suited to my tractor.
  15. F

    Bat wing mower

    Can anyone who runs a 15 foot batwing mower tell me how many horse power are needed to run one for mowing down hay. Thank you.
  16. F

    Rotary cutter brand?

    looks to me like its made in China, according to the tag in your pic.
  17. F

    Question about 3/8 Hydraulic Hard Line Thread vs 3/8 NPT

    I agree with Fritz, my Ford tractor was built in England, a 4610, i could not get a 3/8s npt to fit in the block for a temp gauge, my neighbor was a machinist for GE, he told me it was a British thread pipe fitting,
  18. F

    Why Red vs. Green (and others)?

    Nothing runs like a Deere, except a bad as$ International! just kidding, its like Stihl or husky, Ford or Chevy, Apple or samsung, its what ever works for you!
  19. F

    Cordless impact wrench

    I like my Dewalt 20v maxx xr battery impact, it made sense because I already had a Dewalt 3/8 impact, grease gun and drill from Dewalt, i have also heard good things about the Milwaukee fuel.
  20. F

    What's your guy's opinion on electronic ignition

    I liked points and condenser in my 73 chevy 350, but when I put a sbc 400 in my 84 k20 I used the HEI ignition, i loved it, guess it depends on personal preference. Advantage, no need to adjust point gap, clean points and adjust dwell, electronic ignition, coil goes bad, replace it.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top