(800) 853-2651
SHOP NOW

Search results

  1. T

    8N Rear Axle Assembly

    Could someone please confirm what orientation the two slots shown below go. I assume that they are at the 12 o clock and 6 o clock position. Is that correct? Thank you!
  2. T

    52 8N Rear Axle Hub Noise

    I have a question on the above pictures. I have my 8n apart now and it has been apart for a while. I cannot remember what orientation the two slots under the bearing races go. I am talking about the two slots that are on the left and the right in the above pictures. I assume the slots go top and...
  3. T

    Bondo usage

    Rough fill the hole in with "bondo-glass" fiberglass reinforced body filler and finish it with the regular bondo. Make sure all rust and paint is ground away first. Works for me hope it helps.
  4. T

    1512 Cub Cadet Diesel

    It is a very hard to find part. On my 882 diesel mine was cracked so i welded it. If it goes again I plan on replacing the fan with an electric fan.
  5. T

    WHO REPLACES BROKEN CRAFTSMAN TOOLS

    You have to be careful trying to get an exchange. The part numbers of the tool must match. Problem is if you are trying to exchange an older tool the part numbers are not the same even though the tool is the same. I have had several sockets that I could not get replaced due to the part number...
  6. T

    JD 4100 Compact Won't hold charge

    I went through a similar problem with my 4100. Constant dead batteries and voltage tests appeared like it was not charging. What it turned out to be was a small timer located at the front of the tractor near the radiator. This timer controls the heating of the glow plugs. What was happening...
  7. T

    Solar Powered Pole Light

    Hi I need to replace an outdoor pole light that had the wiring underground go bad. Does anyone have any experience with solar powered outdoor lights, particularly the LED type? Is the light any good? Will they stay light all night? Thanks for your input.
  8. T

    Update Generator Help Needed

    Hi Billy the generator is a Titan 8500 M with a serial number GGT03636. One thing I did notice is that I had an incandescent light plugged into one outlet and with no other load on the generator it was dim but when I plugged in an electric drill the light got brighter. I did try "flashing" the...
  9. T

    Update Generator Help Needed

    Hi did some more testing on the Titan 8500 generator that I am having trouble with. The generator is only putting out 40 volts on both the 120 and 220 outlets. I used a tach and the engine speed is right on the money at 3700 rpm. It is a brushless generator. What could likely be wrong or what...
  10. T

    Generator Help Needed

    Hi Everyone - I have a Chinese Titan 8500 gas generator. My problem is that it does generate but if you plug in a power tool such as a drill or power saw the tool will not run at full speed. The engine on the generator runs fine. I believe it is a "hertz" problem. What would be the likely cause...
  11. T

    Follow up to Rag Discussion

    For my rags I use old clothes. Anyone have any good and easy way to cut up clothing into rags?
  12. T

    Rags

    At the cement plant I work at we buy rags from Fastenal for a reasonable price.
  13. T

    Cheap Shop Floor

    Do you mean skipping the Portland and just using the stone and sand with the tamping?
  14. T

    Cheap Shop Floor

    I am investigating cheap options for a shop I am building in lieu of poured concrete. The shop is 12 x 18 and will be used as a blacksmith shop. I have available to me a good quantity of driveway stone (2" x 0 size with fines) and 6 or 8 bags of cement (not sakrete). What would happen if I put...
  15. T

    Last Post and Thank You

    Dave I am sorry I did not know you and wish I did. I am deeply touched by your post. God bless you and your family Dave.
  16. T

    Old Grinder Flat Belt

    Tried belt dressing, didn't work.
  17. T

    Old Grinder Flat Belt

    I have an big old grinder that used to be driven by a flat leather belt about 3" wide. I had to replace the leather belt and I used a modern synthetic belt from Habisit. The problem is that the new belt does not have enough "traction" and therefore I do not like it. Is there any other type...
  18. T

    Hopefully Last Utility Trailer Question

    Thanks for all the responses on my utility trailer questions! Hopefully this will be my last question. What brand and kind of paint do you like for your utility trailer? I will be painting it black and it will be stored outside. Thanks for your responses!
  19. T

    Trailer Deck Additional Questions

    I am thinking 2 bolts across per board and bolting to every other crossmember. Just seems like a lot of bolts.
  20. T

    Trailer Deck Additional Questions

    I posted earlier about putting a new deck on a utility trailer. My trailer is 7' x 14' and I will be using pressure treated 2 x 10 x 14 ft boards. My question is how many rows of bolts and how many bolts in each board? I will be using galvanized 3/8" carriage bolts and the ends of the boards...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top