(800) 853-2651
SHOP NOW

Search results

  1. A

    Mower

    Can anyone identify this mower? Its not a A18 Highway Mower. Its for sale sale on Marketplace in Goodlettsville TN. Funds are a little short or it would already be here. The mower is probably worth more than the 140.
  2. A

    Thanks

    Thanks for all the responses to my well pump question below. Learn something every day.
  3. A

    Question for the EEs

    Im a bit confused on this one. My submerged well pump stopped working so I pulled it and found that one wire had worn completely through just above the pump. Pretty common problem with the torquing going on down there. It appears that apparently the pump didnt stop working until the last...
  4. A

    Cub Low Boy fast hitch

    Anyone have a one point fast hitch for a cub low boy they would be willing to part with? I?ve been watching the ads but haven?t seen anything. Working on a ?67. Apparently when the previous owner put a woods belly mower on it they ditched all the one point hitch parts. Would like to put it back...
  5. A

    Hobart welder opinion

    Been thinking about getting a Hobart Champion 145 welder. Need a portable but it won?t see heavy duty work so can?t justify the cost of the bigger welders for general repairs and light fabrication. Anyone have experience with one of these or opinions in general? As usual any advice or comments...
  6. A

    Pasture care

    Rainy day here in Nashville and was thinking about my Father always mowing the pastures in the spring. "Keeping the fowlness out" he would say. I have about 80 acres with pretty good fescue but a fair amount of weeds and blackberry. I think he said clip it at about ten inches, but that was...
  7. A

    Onan generator question

    I guess a generator is tool..... Been working on an Onan 6.5 NH built in 1978. There are four leads out of the generator labled M1, M2, M3, and M4. Acording to the manual to wire for 120/240 outputs it says to tie M2 and M3 together and there should be two 120V outputs. (between M1 and M2/3...
  8. A

    How hot is normal?

    Just replaced the coil on a "54 NAA and noticed it"s getting very hot after about fifteen minutes. It has been converted to 12V and the replacement coil is a NAPA IC14SB (no external resister). Is it normal for coil to get to hot to touch?
  9. A

    generator/welder conversion ?

    Just wondering...has anyone converted a portable generator (3000W China cheap) to a welder? I know that voltage regulation would be a problem but that could possibly be overcome by trial and error with the engine speed. Internet is full of conversion instructions using GM alternators, just...
  10. A

    Cub Exhaust

    Does anyone happen to know the pipe size for a cub exhaust? The old one was so rusted it's hard to tell. Looks like 1 1/4" but even after a good cleaning it's tight, doesn't want to screw in. As usual, Thanks in advance.
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top