3500 flooding

dirtnap

Member
Got a 3500 gas. Stopped running a few weeks ago, carb was flooding. Opened up the carb and had a broke float. I rebuilt the carb, new float, etc. Same problem. Fuel dripping out the under side of the carb after only cranking it once. I read somewhere a bad fuel pump would actually deliver too much fuel so I put a new fuel pump in it as well as a new carb. I had also replaced the fuel petcock and screen at the bottom of the tank. So basically a new fuel system and it still floods. Fuel actually drips out the screen on the bottom of the carburetor after only cranking it once.
What am I missing here guys?
 
It's an updraft carburetor system, so any fuel sucked from the carb bowl into the throat of the carb and/or the intake manifold, will drip back down when you stop cranking the starter if it hasn't started. Figure out why it isn't starting, not why it is dripping after cranking the starter without it actually starting.
 
(quoted from post at 13:05:46 10/30/21) Could the governor be causing the flooding? Everything else in the fuel system has been replaced so far.

Have you pulled the spark plugs to see if they're soaked with gas after cranking the starter? Maybe they just need to be cleaned and dried now that you've got the new carb.
 
(quoted from post at 10:08:10 10/30/21)
(quoted from post at 13:05:46 10/30/21) Could the governor be causing the flooding? Everything else in the fuel system has been replaced so far.

Have you pulled the spark plugs to see if they're soaked with gas after cranking the starter? Maybe they just need to be cleaned and dried now that you've got the new carb.

Brand new plugs as well. Good spark.
 
(quoted from post at 04:47:36 11/01/21) Update here,
When I crank it it'll fire, maybe a couple revolutions then it dies.
Any more ideas?



Sounds like mixture is not rich enough for long enough.
 
(quoted from post at 07:47:36 11/01/21) Update here,
When I crank it it'll fire, maybe a couple revolutions then it dies.
Any more ideas?

I agree with showcrop, sounds like a mixture issue. After you get it to fire like that, pull one of the plugs and check its condition. Is it wet, or grey, or black?
 
(quoted from post at 07:02:06 11/01/21)
(quoted from post at 07:47:36 11/01/21) Update here,
When I crank it it'll fire, maybe a couple revolutions then it dies.
Any more ideas?

I agree with showcrop, sounds like a mixture issue. After you get it to fire like that, pull one of the plugs and check its condition. Is it wet, or grey, or black?

The plugs are wet and black.
 
Brand new plugs as well. Good spark.

...

The plugs are wet and black.

All we know is that the tractor stopped running and that the original carb "started flooding" (maybe that was just unburned fuel dripping out due to gravity because of some other unknown reason that caused it to stop running?). Then at some point the fuel pump, the carb, the fuel petcock and screen at the bottom of the tank were replaced as well as the spark plugs.

Maybe a more detailed timeline of when you did what would be in order.

The spark plugs are now fouled. Have you cleaned and dried them and reinstalled once everything else in the fuel system was replaced, or were the plugs installed at some point earlier and you haven't had them out to clean or dry them since?

Also, how are you determining that it has a "Good spark"?

This post was edited by Sean in PA on 11/02/2021 at 10:03 am.
 
(quoted from post at 10:02:07 11/02/21)
Brand new plugs as well. Good spark.

...

The plugs are wet and black.

All we know is that the tractor stopped running and that the original carb "started flooding" (maybe that was just unburned fuel dripping out due to gravity because of some other unknown reason that caused it to stop running?). Then at some point the fuel pump, the carb, the fuel petcock and screen at the bottom of the tank were replaced as well as the spark plugs.

Maybe a more detailed timeline of when you did what would be in order.

The spark plugs are now fouled. Have you cleaned and dried them and reinstalled once everything else in the fuel system was replaced, or were the plugs installed at some point earlier and you haven't had them out to clean or dry them since?

Also, how are you determining that it has a "Good spark"?

This post was edited by Sean in PA on 11/02/2021 at 10:03 am.
Actually Sean I described the situation but I'll do it again cause I really appreciate the help. The first time it started giving me trouble and flooding I Opened up the original carb(Holley) and found a broken float. It was in 2 pieces. I rebuilt the carb with no success. At that point I just started replacing parts since they're cheap (compared to a new tractor) and the tractor's new to me. New carb, plugs, fuel pump, cleaned the tank, new petcock and screen. After all that I have the same issue. Sometime it sounds like it wants to start and run but just won't "catch".
When I got the tractor I had replaced the points with a Petronix unit. I have pulled a plug and cranked it getting a "good spark"
 
New carb, plugs, fuel pump, cleaned the tank, new petcock and screen.

Was that the exact order? How much cranking of the starter occurred after replacing each individual part? A more exact timeline, including what symptoms changed, if any, after each part was replaced will help tremendously. Simply throwing a large number of parts at a problem with no actual troubleshooting can be a waste of both your time and your money. Not providing the specific details as to what you've done and any changes in symptoms along the way becomes a waste of our time.

You still haven't answered my lat question in my previous post... How are you determining that it has a "Good spark"? What I mean by that is, did you use an in-line spark tester or are you just "eyeballing it"? If you just eyeballed it, what color is the spark, and how large of a gap will it jump?
 
(quoted from post at 14:00:57 11/02/21) [
Was that the exact order?
-opened up original carb after I noticed flooding after cranking it a half dozen times, found float in two pieces.
-ordered rebuild kit, petcock, plugs, cleaned the tank, installed all those parts.
-Tried starting, got lots of fuel dripping(pouring)out of bottom of carb.
-Bought new and installed carb and fuel pump. Checked spark at that point. It fires now, but only runs briefly as described previously. That's pretty much where I'm at presently

How much cranking of the starter occurred after replacing each individual part?
-Enough that I noticed fuel in the oil and changed it before I replaced carb and pump. Also note that the starter was replaced back in the summer. It has run since the new starter and battery.
A more exact timeline, including what symptoms changed, if any, after each part was replaced will help tremendously. Simply throwing a large number of parts at a problem
-I agree, Up to this point I wouldn't consider the number of parts and money I've spent a lot, and in this case I consider it peace of mind since this tractor is almost 50 years old and I like to have things that are reliable(can't afford anything more expensive on a firefighter salary) so replacing potential wear items and problems down the road is within my comfort zone.
Plus with no actual troubleshooting can be a waste of both your time and your money.
-I was troubleshooting the whole time
Not providing the specific details as to what you've done and any changes in symptoms along the way becomes a waste of our time.
-I apologize for wasting your time, I honestly thought I was clear in my previous posts.

You still haven't answered my last question in my previous post... How are you determining that it has a "Good spark"? What I mean by that is, did you use an in-line spark tester or are you just "eyeballing it"? If you just eyeballed it, what color is the spark, and how large of a gap will it jump?
-I can't give you specifics on that. I laid the plug on the head, hit the starter and got, what appeared to my 54 year old eyes, as a "good spark", bright and blue I believe. I've seen a $hitty spark before and this wasn't one.

Hopefully I've answered your questions. This has been a long project since I'm not working on it every day and I'm recovering from an on the job injury at the same time.
 
As I said, and others have backed me up on, some fuel dripping out of the carb after cranking the starter is normal in an updraft system. Try placing the plug so that it is at least 1/4" away from any ground spot on the engine and crank the starter. The spark should be bright blue/white and be able to jump at least a 1/4" gap.
 
I did as you described. The spark was exactly as you described. The engine sounded like it wanted to start. Exactly as before. It will run for maybe a second then die. When I did this, and I cranked it once and only once, the fuel was literally running out of the bottom screen of the carb. It was a constant stream for almost a minute.
 
Sounds like the carb may be adjusted too rich. Or maybe there is some blockage in the intake that is causing too much vacuum? Is all of this with the air cleaner connected to the carb? If so, have you checked to make sure that the air cleaner and intake tubes aren't clogged?
 
(quoted from post at 13:50:49 11/04/21) Sounds like the carb may be adjusted too rich. Or maybe there is some blockage in the intake that is causing too much vacuum? Is all of this with the air cleaner connected to the carb? If so, have you checked to make sure that the air cleaner and intake tubes aren't clogged?

You have been reading my mind Sean!!!!
I read this thread three times, start to finish, and never did I read where he had cleaned or checked the air tube/cleaner for any debrie/dirt........can cause air to fuel mix non-existance!!
Air, fuel, elects' and timing......needed to properly run, and all at the right time.!!!

Gary?
 


I will chime in here again, and yes, firefighters may not get paid a whole lot but they mostly get great retirement, and they get paid for doing something that most people have to pay a lot to do. (25 year nozzle-man here). Thank you for your service! You keep referring to flooding and let me try to clarify that flooding refers to excess gas in the cylinders, NOT IN THE CARBURETOR THROAT. Gas running out of the carburetor when the carburetor is an updraft type, DOES NOT indicate flooding. My own experience is that with the air intake tube disconnected, which I usually do when I have this situation, if I crank for over five seconds without the engine starting, that I am going to have probably in the neighborhood of four ounces of gas running out the carburetor throat. Then if I stop cranking for ten seconds the float bowl will refill and if I repeat I will get another 3-4 ounces of gas.
 
(quoted from post at 12:50:49 11/04/21) Sounds like the carb may be adjusted too rich. Or maybe there is some blockage in the intake that is causing too much vacuum? Is all of this with the air cleaner connected to the carb? If so, have you checked to make sure that the air cleaner and intake tubes aren't clogged?
The air cleaner is off right now as I had to take it and the radiator off to get at the fuel pump. The intake hose is connected to the carb still. You may be onto something though. Maybe a mouse has made a nest in there. I'll check it tomorrow. Should run with nothing attached to the carb right?
 
You're right, I mistakenly called it flooding.
What was the issue when you had to disconnect the intake tube? Clogged filter?

This post was edited by dirtnap on 11/04/2021 at 03:12 pm.
 
(quoted from post at 15:10:20 11/04/21) You're right, I mistakenly called it flooding.
What was the issue when you had to disconnect the intake tube? Clogged filter?

This post was edited by dirtnap on 11/04/2021 at 03:12 pm.


No, it needed more choke and a little less air through the air jet.
 
Here's where we are today.
-I removed all intake tubing and inspected it. There is nothing blocking it.
-I installed new plugs.
-Adjusted the idle screw 1 1/2 turns out.
-Adjusted the throttle plate till I got just a bit of movement.
When I tried to start it it jumped to life then dies suddenly, I tried this with the intake hose off. There was no fuel overflowing the carb today.
Humor me here and educate me, the throttle linkage that goes to the front of the engine, that's the governor right? Explain to me how that works. I can't find much in the service manual. What is the position that that should be in when it's not running? Sean seemed pretty sure that wasn't the problem but I'd like to learn more about it. I have no experience with a setup like this.
Thanks
 
My Ford Factory Service Manual has a section titled "Carburetor and Governor Linkage Adjustments" in the Fuel System section, but it only covers adjusting the carb itself. It looks like the governor linkage adjustment information was left out.

The governor, and its linkage adjustment are covered in the I&T FO-31 after market service manual starting at paragraph 164.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top