49 front mount dizy

Bohinny

Member
What are the symptoms of having point gap set to close on the front mount dizy. The tractor has been very hard to start when hot so I took the the dizy off to regap and retime when I put it back together the thing is running like $hit. The firing order is correct and there is plenty of fuel. Also when I was checking to make sure the plug wires were on the plugs good with a screwdriver the spark was jumping to ground thru the boot but not jumping fire when left alone. I am new to the whole points thing as this tractor is 35 years older then I am. Any help would appreciate it. PS the thing was running fine before just hard to start when hot
 
(quoted from post at 20:15:45 02/25/11) What are the symptoms of having point gap set to close on the front mount dizy. The tractor has been very hard to start when hot so I took the the dizy off to regap and retime when I put it back together the thing is running like $hit. The firing order is correct and there is plenty of fuel. Also when I was checking to make sure the plug wires were on the plugs good with a screwdriver the spark was jumping to ground thru the boot but not jumping fire when left alone. I am new to the whole points thing as this tractor is 35 years older then I am. Any help would appreciate it. PS the thing was running fine before just hard to start when hot
A little close will alter timing & dwell a little.....no big deal. A lot too close, as in barely opening, and it will be "running like $hit.", or not at all.
 
Sounds like you may need new copper plug wires ("firing thru boot with screw driver.
A worn bearing in the distributor can also cause eratic running. Try setting the gap wider and see how it runs.
Is this a 12 volt conversion or still a 6 volt?
Charles Krammin SW MI
 
Like JMOR said, a little narrower on the gap is no big deal. Once you get to less than .010, you're gonna have problems.

And, as Charles said, replace your wires.

Points aren't all that difficult to deal with......when you are as old as most of us around here & have been fooling w/ them since the day before dirt.

Usually burned points will have pits on one side & raised areas on the others. Sometimes they just wear unevenly. They will most always discolor as they have a coating on the surface. The usual causes of burned points are absence of cam/wearing block lubricant, condenser failure, a decreasing gap caused by wear on the rubbing block, mis-alignment, sanding w/ a point file, excessive current, setting an incorrect gap, leaving the ignition key on w/ the points closed, use of incorrect cam lubricant & poor quality metal.

You can change points everyday & it will not fix bad bushings. If you are having trouble w/ points failure, check the shaft. If you detect movement, chances are it needs new bushings.

The next trick to points lasting a long, long time is annual maintenance. (tip # 40) No matter how well it's running, pull the distributor, check the gap & put a dab of points lube on the cam. Not bearing grease or Vaseline; use the correct lube.

Quality parts are critical to longevity. Having learned the hard way, I most always use Blue Streak brand points. They are made by Standard parts & available at many auto parts stores. (frontmount points also fit a 48 Ford as I recall) Beware of sticker shock: $16-18 a set. My next choices are Wells or Echlin. Look for a brown rubbing block. Unfortunately, many folks have experienced problems w/ points made by Tisco, Sparex, A&I Products and any TSC ignition parts..

Correct points installation & gap is also important. Make sure the blade is at a perfect right angle to the points & you want to feel just the slightest bit of drag when you pull the blade through the points. Make sure the blade is clean & that you dress the new points by running some card stock or a piece of brown paper bag through them. Gap is .015 on the frontmount, .025 on the sidemount on all four lobes of the cam. Make sure the points align correctly.

Even as tight as I am, I always change the condenser when I change the points…….and then I toss the condenser in the “used” parts box. A bad condenser is rare; you can tell if the points are pitted/burned w/ metal transfer.

Good hold-down screws are important. (tip # 37) If the heads are wallowed out, what do you think the threads look like? You can use machine screws as temporary replacements, but you should use the OEM Fillister head screws. The larger head is there for a reason. If you do use standard machine screws, make sure they aren’t too long & interfere w/ the advance weights. Always use star washers under the screws.

When I was 16 years old making $1.25 an hour & a set of points cost $1, I filed points. I must have been good at it because I recall it was almost a weekly exercise. If you ever file a set of points, you will remove the metallic coating on them & reduce the life span considerably. Unless you plan to keep on filing them, plan on replacing them pretty soon!

And lastly………it does not matter if it’s 6 volt or 12 volt, you must use the OEM ballast resistor on a frontmount. Too much current to the points will burn them up in short order (leave the key on with the points closed & you will experience this “learning point” in about 3 minutes, tip # 38) For a 12v conversion on a frontmount, you probably need another resistor in the circuit as well but unless you measure the coil resistance, you will not know for sure.
50 Tips
 
it is 12v and the point are less then year old premium set from this web site. from the decription on setting the points i was probably forcing the the guage more then i should have. any ideas on the hard to start when hot. the tractor is at the farm 2 hours away so it will be sometime before i get a chance to work on it.
thanks
 
Bohinney........you write......"tractor has been very hard to start when hot"......there are 4-common runtime issues with the 4-nipple frontmount dizzy.
1) runs fer about 1-min and quits; restarts innna'bout 5-mins; BAD condenser; NOT yer problem
2) runs fer about 5-mins and quits; restarts innna'bout 10-mins; CLOGGED intank fuel filter; NOT yer problem
3) runs fer about 15-mins and quits; restarts innna'bout 30-mins; BAD weaksister ignition switch $15 (cheap) Most likely yer problem
4) runs fer about 1-hr and quits; restarts innna'bout 4-hrs or overnite cooldown. Could be yer problem, since you did NOT specify how long yer tractor runs before you start have runnin' problems.

As fer yer points gap question; too close and them condenser aided sparkies will jump the gap and BURN yer points. Too wide and you will have weak sparkies; 'cuz it takes time (points closed) to make hot enuff sparkies from the magnetic field that collapses when the points open.

Remember to always POLISH yer NEW points after installation. (0.015" gap) I use a dollar bill but you can use heavy brown paper grocery sack. Just clamp the paper between closed points and pull. WHY? 'cuz even NEW POINTS have invisible corrosion on surfaces. And besides now you'll haff sumptin' to bragg about. .......Dell, yer self-appointed sparkie-meister
 
(quoted from post at 22:44:18 02/25/11) it is 12v and the point are less then year old premium set from this web site. from the decription on setting the points i was probably forcing the the guage more then i should have. any ideas on the hard to start when hot. the tractor is at the farm 2 hours away so it will be sometime before i get a chance to work on it.
thanks
ou last set the point gap a year ago........you can just about bet the farm that the gap has changed since then......time to re-set.
 
I have had trouble in both my front mount dizzy and my side mount 12 volt conversion, quiting and not starting when warm. I diagnosied both as the coil heating up and breaking down the insulation inside it. The only way it can be determined is to try a known good coil,(in your case a new 12 volt coil) and see how it works.
I also determined the 12volt coil was heating up and destroying them was NOT HAVING A BALLAST RESISTOR IN THE CIRCUIT, even though I was told I didn't need it. The front mount coil also gets more heat from the radiator, then a side mount does.
Also most 12 volt alternators are negative ground, and the old 6 volt was positive ground.
The spark is suficient to run the tractor, but the reverse in polarity (with only one electrical connection on front mount coil) to cause the flow of electricity to the spark plug to be reversed (Spark is then thru the grounded block, thru the bottom of the sparkplug, to the center insulated portion, to the spark plug wires to the points, to the coil. (This can be observed by idling with aplug wire off, and watching wnich way the spark is going) On a sidemount coil the solution is very simple, reverse the wire on the coil from +/- (switch/distributor or termonology like that on coil)
My recommendation, in your case is to live with the negative ground alternator, 12 volt coil, with ballst resistor in circuit ( ballast resistor heats up after starting and runing and reduces current thru coil and points, therby reducing heat buildup in thise components.
Charles Krammin SW MI
 
" any ideas on the hard to start when hot"

Well, here's one idea:

" i was probably forcing the the guage "

If the gap was too small a year ago, it's less now. And you might have burned the points.

Go back & re-read what Charles & I said about resistors & coils. Unless you have 4 amps or less current going to the coil, it could be going bad. As could your points.
50 Tips
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top