550 Ford backhoe

rlp in Co.

Well-known Member
I am having problems getting this started after I cleaned the filter in the pump. Please don't tell me that I shouldn't have removed the pump!I put a gauge on it and it has 9 pounds pressure cranking. I think I might have turned the pump drive gear when I removed the pump. I can easily tell when the piston is at top dead center by removing the number one injector, but how can I tell when the pump injects the fuel? Can I tell from the location of the locating pin?
 
Thanks for that answer! I was going to try to move it a tooth or two. There is fuel coming out when I crack the lines, but it won't start no matter how much I crank it.So what could be wrong? How much pressure should the transfer pump make at crank speed. I didn't turn the engine after I took the pump off and put it back on.
Maybe I can take an injector out and see if it injects fuel.
 
You shouldnt have to take the injector and watch it . If fuel is being injected there will be white smoke billowing out as you crank it. If all this cranking and no noteworthy smoke, something is wrong with the pump. 201 not the easiest fuel system to prime, but if you have fuel at the injectors, its getting ready to go. By fuel at the injectors, I mean squirting out foamy fuel , not just making the back of the nut damp.
 
I have foamy fuel at the injectors but no white smoke from the exhaust. I already have an injector loose so I'm going to go try to hook it up and see if fuel is actually being injected. I don't know if I can do it without bending a line
 
I should have been clearer about the foam thing. What I meant was when shes getting ready to go, the fuel is clearly shooting out of the nut, with a few air bubbles on the side. If all you have is foam, you still have air in the filter, or the tank is nearly empty. Before you take anything else apart, remove the fuel line from the transfer pump inlet and make sure you have gravity fuel flow completely free of air at the pump.
 
Thanks for the reply! Well I just hooked up an injector but I don't think it was a valid test because I couldn't hook up the fuel return line. There was no fuel from the injector. Should the pump shoot a strong spurt of fuel out with the lines unhooked? Because it doesn't. I have plenty of fuel to the pump and plenty of fuel from the return line. Did you read that I have 9 pounds of fuel pressure? But I don't know how much it's supposed to have.
I have put 19 years if wear on this starter! I wish I could put a gauge on the injector line to see how much injection pressure it puts out.I guess the only thing left to do is take the pump back off and see if some dirt is blocking something up.
 
The return line not being hooked up will have no bearing on your test. If you have solid fuel coming out of the top of the pump (return line), I think we can eliminate air in the pump. As far as the fuel shooting out of the lines , I have held a pump like that in my hand and spun it, the fuel shot out but installed on a motor at cranking speed it would be hard to say how much could be seen coming out with no pressure against it. Thats where the injector test comes in handy. The pressure check you did was really intended to be taken with the engine running. I thought I read something about it being around 48 psi at idle speed. If you have 9 at cranking speed that ought to be enough to start the engine. I guess at this point all you can do is remove the pump and go over it again. It ran when you took it off, so carefully inspect the areas of the pump you disassembled. There must be some diagrams online somewhere to help you, that would make it much easier.
 
DO NOT DEADHEAD A PRESSURE GAGE TO INJECTION LINE!!! That's NOT how to test the pump, the injectors control the opening pressure, NOT the pump. The pump MUST pressurize, time, and meter the fuel THROUGH the injectors..
 
Well I took the pump back off and will try again tomorrow. I mixed some diesel and gas together because it wouldn't run with pure diesel. I dribbled about a pint of fuel in and the engine ran at maybe 1000 RPM, but not on the pump.The fuel pressure was at 39 pounds. So either I did something wrong or there is dirt somewhere.
It was an interesting experiment. I first tried to run the engine on propane; it wouldn't even pop. Next I tried pure diesel; it would pop but wouldn't stay running so I mixed some gas in with the diesel. It then ran but knocked a little. I figure that wouldn't hurt the engine. This engine has knocked for 20 years. Someone said I need new injectors. Not sure why. Maybe the injection pressure us too low?
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top