641 broken gear

601Al

Member
My 641 with a 4 speed transmission has a broken gear. I’m not sure if anything is broken on the bottom shaft, but I didn’t see any pieces that I could contribute to the bottom. Is there a way to remove the top shaft and peek below without performing the dreaded double split? I have a manual, but I am hoping that someone here has a secret trick to get the top shaft out. Thank you in advance for helpful replies. Al
 

Attachments

  • IMG_4190.jpeg
    IMG_4190.jpeg
    134.2 KB · Views: 0
  • IMG_4191.png
    IMG_4191.png
    1.4 MB · Views: 0
  • IMG_4188.jpeg
    IMG_4188.jpeg
    2 MB · Views: 0
  • IMG_4123.jpeg
    IMG_4123.jpeg
    1.9 MB · Views: 0
A split it will be. Those transmission's are EZ to repair most all need new bearings anyways. Just for reference the neutral gate must align straight if its off you have a bent fork.

More info


shift gate.jpg
 
A split it will be. Those transmission's are EZ to repair most all need new bearings anyways. Just for reference the neutral gate must align straight if its off you have a bent fork.

More info


View attachment 166963
Thank you Sir. I was afraid that would be the case, but I knew the membership here has much more knowledge than I. I was hoping after the engine rebuild, hydraulic overhaul and paint that I was done!
 
Thank you Sir. I was afraid that would be the case, but I knew the membership here has much more knowledge than I. I was hoping after the engine rebuild, hydraulic overhaul and paint that I was done!
I needed to service a 5 speed on a 901. I custom built a rolling cart to facilitate. It allowed me to easily remove the transmission from the rear end and then served as a work bench for disassembly/service/reassembly. Made the job straightforward, very controlled. It's been quite handy for other things since then. You'll need a shorter one, but I'm confident it would work similarly.

IMG_0631.jpg


IMG_0633.jpg
 
I needed to service a 5 speed on a 901. I custom built a rolling cart to facilitate. It allowed me to easily remove the transmission from the rear end and then served as a work bench for disassembly/service/reassembly. Made the job straightforward, very controlled. It's been quite handy for other things since then. You'll need a shorter one, but I'm confident it would work similarly.

View attachment 166964

View attachment 166965
That’s fantastic. I thought about using my cherry picker for the middle, but that stand is WAY more controlled! I have an engine hoist at the front of my shop to hold up the front of the tractor, and a floor jack for the back. Thanks for the idea!
 
Be aware there is a coupling on the pto engagement shaft. This coupling/collar will install either direction but only works in the CORRECT direction. Note how it comes off if pto is working properly now, otherwise pto lever can't engage coupling/collar and re-split is required.BTDT.
 
Well boys, I’m in the thick of it. Brought my old engine pulling frame and shoehorned it in the shop to hold the front with the help of a chain house and bottle jack. The transmission has my old transmission jack and cherry picker for support. The steering components are hooked to a rafter to keep things upright. The rear has a floor jack and a 2,500 pound trailer jack on duty. I was able to source used gears to put a new reverse on the counter shaft and second on the main shaft. I’m just waiting on a new bearing from the main shaft that got mangled while pulling them apart, the gasket sets, and a new clutch kit, because why not while it’s apart. Thank you all for the thoughtful advice.
 

Attachments

  • IMG_4294.jpeg
    IMG_4294.jpeg
    2.2 MB · Views: 0
  • IMG_4280.jpeg
    IMG_4280.jpeg
    2 MB · Views: 0
  • IMG_4282.jpeg
    IMG_4282.jpeg
    1.9 MB · Views: 0
  • IMG_4307.jpeg
    IMG_4307.jpeg
    1.9 MB · Views: 0
  • IMG_4297.jpeg
    IMG_4297.jpeg
    1.8 MB · Views: 0
  • IMG_4295.jpeg
    IMG_4295.jpeg
    2 MB · Views: 0
  • IMG_4281.jpeg
    IMG_4281.jpeg
    1.9 MB · Views: 0
  • IMG_4309.jpeg
    IMG_4309.jpeg
    2.9 MB · Views: 0
  • IMG_4311.jpeg
    IMG_4311.jpeg
    2.8 MB · Views: 0
Last edited:
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top