70 D NOISY clutch

JMJ

New User
I"ve got a "55 70D that ive been having clutch problems with. Since i bought the tractor the clutch has been loud really rattling and clunking, and would bind up and not release with out jamming on the brakes a few times.
I knew the driver and disks were pretty badly worn so i bit the bullet and put in a new driver, two floating disks, new linings, and new dogs and new adjusting bolts. Now the clutch operates much smoother and releases and stops spinning like it should but the problem is now it is REALLY LOUD when released id expect some noise but this is the worst sounding two cylinder clutch ive ever heard. Anybody got any ideas of what can cause this thing to be so loud?
 
The bearing inside the pulley can cause those sorts of noises. It may be in need of replacement. Replace the bearing and repack with hi temp wheel bearing grease.

While you have it off if you didnt already pack the toggles/pins/dogbones/operating sleeve with that same high temperature wheel bearing grease. It will slow wear and make for a much smoother operating clutch.
 
on my 48 b i had to replace the brass bushing on the inside of the pulley assy next to the main bearing too. i don't know if your tractor has one or not. also you need to examine the bearing that supports the first redcution gear. you can get to it on my b by just removing two blots on the frg cover just in front of the right brake. you may find it shot. there is a ring in there you have to take out to get the bearing out. on some tractors people taped a hole for a grease fitting and put on in the end of the cover to make it ease to keep it lubed.
 
Well i went out and pulled the clutch brake off of the tractor, unhooked the clutch lever from the fork arm, and grabbed ahold of the pulley and gave 'er a good wiggle and i guess i do have an apprecialble amount of radial play. So ill be off to find a bearing and race and a bushing Monday. Just as well put the whole works in it and just get it over with. Hopefully that will quiet it down back to a reasonable level, then i wont have to worry about the Farmall crowd talkin about that two cylinder that sounds like its ready to fly apart every time i disengage the clutch.
 
you need a service manual first. take it apart before you go looking for parts. there is a lot more in there that cold be worn out than you've found so far. also don't forget to check the beraring the supports the frg. its a small thing, but can cause a lot of noise and problems with the clutch. also you need to set the flywheel spacing correctly in order to adjust your clutch correctly. if you have to remove the clutch fork and take it apart to repalce the spring that helps hold the weight of the fork up off of the cpulley assy be sure and mark the grooves where you can put it back together at the right spot. you'll understand once you get into it. to remove the pulley assy from the crank you need a good puller. the one i sed is shaped like and "H". there is two holes in the piece that needs to be used to bolt the pulley two. don't run the bolts in to deep as there is another clutch disk in behind this part. also, don't be afraid to apply just a little bit of heat to the puleey asy to make it come off even with the puller on it. i coldn't get mine to bludge and i took a torch and jst ran it around the whole thing for about 4 or 5 seconds and it popped right off. good luck/ em me directly if i can help and i'll give yhou my phone number. i'm not familiar with the 50 so instructions are what i did for my 48 b, but i expect they are close to being right for your tractor.
 
John, He says it's noisy when the clutch is disengaged. The FRD does not turn unless the clutch is engaged. The bearing may be bad, but not the noise he is trying to fix at the moment.

The bearing in the clutch pulley will fix his issues. Be sure to get a new felt as well. I'm sure yours is long gone from deterioration.

I would not worry too much about the main bushing unless there seems to be difficulty after the bearing is replaced. The bushing will be expensive if it is available at all and will require a press to press in and out. That can come later if necessary. No reason to just change parts unless they cause a problem. You dont change your A/C compressor on your car just because. You wait until there is a problem then you change it.
 
John... I just read more of your post. He does not need a puller on a 70. He needs two bolts to thread into the driver which press against the back of the pulley not the clutch disc. He is already well versed in this operation since he noted that he replaced his "T" bolts. I'm putting this info here so when a novice reads historical posts he wont get the wrong idea.
 
Well i actually just had the whole assy off and apart on friday, and every thing but the operating sleeve, drive gear and the pulley its self (bearing and bushing included) is new in it right now. I looked at the bushing in it and it doesnt appear to be worn at a taper like i figured it would show if it was worn but i didnt have a mic to actually measure it so i just packed the roller bearing and threw it back togeather. The bearing, race and bushing are all still available $98 for the bearing and race i think and $48 for the bushing. I think i'm gonna start with just the bearing at least til i get done using it this next couple weeks til i get time to take it to a shop to get the bushing changed.
 
I had a 720 that did the same thing for noise. Quiet when engaged, very loud when disengaged. It was a loose flywheel.

Dont just check it with the cover off. Take the nut off and check it. When you have the clutch back togeather and the flywheel cover off, set the endplay for the crank. Its worth the time to check and set.

Jake
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top