8N Carburator Problem

My "48 Ford 8N tractor (front distributor) quit on me, and I saw that gas was running out of the bottom of the carb lower body. Closer inspection revealed a recessed screw had fallen out. I removed the lower body, and reinstalled with a temporary plug, but now misses badly. Can anyone tell me what that part is? - either it was not simply a drain plug, or I reassembled something wrong.

The missing screw is in the center of the lower body, LEFT of the larger drain screw that faces to the rear of the engine (air intake).
id15146.jpg
 
(quoted from post at 21:41:01 09/18/08) My "48 Ford 8N tractor (front distributor) quit on me, and I saw that gas was running out of the bottom of the carb lower body. Closer inspection revealed a recessed screw had fallen out. I removed the lower body, and reinstalled with a temporary plug, but now misses badly. Can anyone tell me what that part is? - either it was not simply a drain plug, or I reassembled something wrong.

The missing screw is in the center of the lower body, LEFT of the larger drain screw that faces to the rear of the engine (air intake).

That is a drain.

It has a thing that is made of these little bity brass balls like, pressed hard together, and it is supposed to drain any extra gas in the carb out on the ground, while at the same time, not letting dust into the carb.

It sounds like your float, needle valve assembly, is leaking, or has trash in it.

One of the best things that you can do to these carbs, is to make sure they are good and clean, from the fuel, to the gas tank, to the inside of the carb.

Make sure that all passages in the carb can be blown thru with an air compressor, and a rubber tipped blow gun.

Make sure the float is set right.

With your new "improved" plug, you may fill the carb, the intake, the cylinders, and finally the crankcase with gas.

Always turn the gas off when the tractor is stopped, and not running.

Your pic seems to freek me out for some reason.

I reversed it, it does look better to me.

111d15146.jpg
 
Steve -

That's actually not a screw. If I recall correctly, that is a tightly packed wad of bronze, or brass, balls that is pressed together like a plug. I believe its called a strainer.

They are available, but I don't think from this site.

Part number 9N 9694

Check a few of the other sites - they run about $12.00.

Joe
 
OK, thanks, Dunk! - I could not imagine what I did to cause it to miss so badly, just by removing the lower body, plugging the hole, and re-installing ... guess I broke some dirt loose somewhere? I'll remove the whole carb, disassemble, and clean it - see what that does.

BTW, do you think JB Weld will be alright, to 'permanently' plug the drain hole? No idea where to find another real plug.
 
(quoted from post at 22:06:02 09/18/08) OK, thanks, Dunk! - I could not imagine what I did to cause it to miss so badly, just by removing the lower body, plugging the hole, and re-installing ... guess I broke some dirt loose somewhere? I'll remove the whole carb, disassemble, and clean it - see what that does.

BTW, do you think JB Weld will be alright, to 'permanently' plug the drain hole? No idea where to find another real plug.

Absolutely do not plug it.

If you can't find one, we will find you one, or we will tell you something else to replace it with.

Wait on the other guys, there are many very resourceful folks here, and I am about drunk.
 
You can buy any amount you want at you local DEERE dealer for just over $4.00.

MS/DEERE part # 95-78. (The DEERE parts system recognizes to Marvel-Schebler part number.)

Just have them get it in on their next stock order so there's no freight.
 
OK, thanks again, All! - the 'local' John Deere store is ordering me a replacement strainer (as Bob suggested) - cost ~$6 - picking it up tomorrow morning.

I may just plug it in and see how she runs first ... if no luck, it's a tear-down, clean, and readjust. If that doesn't work, I guess a new carb?
 
(quoted from post at 18:15:33 09/19/08) OK, thanks again, All! - the 'local' John Deere store is ordering me a replacement strainer (as Bob suggested) - cost ~$6 - picking it up tomorrow morning.

I may just plug it in and see how she runs first ... if no luck, it's a tear-down, clean, and readjust. If that doesn't work, I guess a new carb?

I have so far not seen one of these carbs that couldn't be cleaned and fixed.

That doesn't entirely mean that there aren't any that can't be fixed.

But that I bet a little TLC and it will work just fine.
 
OK, I got my $6 part at the JD dealer yesterday.

But one more question: it's a simple little 'strainer' plug, i.e. not any kind of 'screw' or bolt (no threads). However, the hole in the bowl it came out of is threaded.

Does it just pop in? - if so, will it stay?

Going out in a minute and remove the whole carb, to get a better look.
 
Well, I was mistaken about the hole being threaded - you just tap the porous strainer 'plug' in to the hole and that seemed to do it ...

So I pulled the little carb and did that, went to put it back on, and as my luck goes, one of the carb studs broke when I was tightening it.

So pulled it off again, drilled out the broken stud, and luckily, AutoZone had a set of (water pump) studs the same size.

Put it back on again with new stud, fired it up and it ran great for about 5 minutes. Cut it off, but now it won't start.

Back to the drawing board!
 
Well, maybe I'm an Idiot? - went back last evening and it started and ran fine - maybe I had the key off?

Thanks again for all the help!
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top