8n lighting

GrantH

New User
I am pretty new to restoring ford tractors, and I had a
question about lighting for an 8n. My tractor runs real
smooth with the original 6 volt system and turns over nice. I
am wanting to add headlights and a work light to my project
however I dont know if I should switch over to 12 volt to do
that. I am afraid if I buy 6 volt specific hardware and hook it
all up, Itll be worse than holding 2 candle sticks and itll be
real dim and hardly worth the effort. Does anyone have any
experience with headlights and the original 6 volt system
how bright they are? Should I just switch over to 12 volt or
would 6 be enough?
 
Grant,
Welcome to Yesterdays Tractors.
How much night driving are you gonna do with the tractor?
A 6V 8n generator is barely adequate to keep the battery charged, run the ignition and keep a couple of dim headlights going.
Yes, a 12V alternator will run several sparkling bright lights, your old 8 track tape player and maybe even an electric seat heater. But if you don't need those things, what is the point in converting?
Dont't get me wrong. I am very much a 12V advocate.
But for lights?
Meh.
My tractor goes to bed with the chickens.
 
Welcome aboard the wonderful world of FORD TRACTORS! ALL FORDs were originally 6V/POS GRN but don't assume just because you have a 6V battery you are wired for that system. There is much to learn and know before you even turn ovetr the engine so if you don't already have them, get THE ESSENTIAL MANUALS and read religiously. They are the best investment you can make for your new tractor. You need to know if your 8N is the early style with the front mount distributor or the late 8N with the angle/side mount disributor. The early front mount distributor is a tricky item, and most misundertood feature. The unit must be timed, tesed, and mounted correctly. If you get it wrong, you will destroy the base at first power up. The Angle Mount setup was a better design andused on all FORDs after 1950. There are differences in the two. Next is lighting kits. ALL FORD TRACTORS never had lights from the factory until the 800 Model in 1954. Lighting kits were always a dealer supplied optional accessory up til then. 12V didn't come along until the late 1950's with the diesel models. One of the advantages with 12V is the lights. 12V lamps burn brighter than 6V. You don't have to switch over to 12V though if you are working just fine on 6V. There is more to swapping out to 12V than just changing the battery. Know how and what you are doing before doing anything. Many attempts at wiring lights have ended up with electrical issues because they were done wrong. One is to leave the lamps at 6V when switching to 12V. You will burn out a 6V lamp using a 12V power source; it's basic electronics/OHMS LAW. The original MPC's (Master Parts Catalouge) have lighting sketches with wiring and the parts needed. Dennis Carpenetr repop all the lights exact-as-original but originals also can be found on auction sites and ads. I advise to wait to add lights and concentrate on the more important features of your 8N. You want mechanical and electrical systems operating corretly first. Then you can decide if you want to heange out to 12V. A 12V setup will spin the starter motor faster, good for a worn engine, burn brighter lights, and run 12V things like sprayers and 8-TRACK PLAYERs. But there is nothing wrong with the 6V system eiether. FACT: Wheter 6V or 12V, 99.98% of all non-starting issues are due to incorrcet wiring, and wrong ligting accounts for a good percentage of that. Get the manuals and related documents and do a lot of research first. I can help with your wiring and lighting when you get that far. I have original lights; tail, head, and work, restored for sale too.



FORD TRACTOR OEM WIRING FOR LIGHTING KIT:
bDlvePih.jpg
TXqFYsih.jpg



FORD 8N TRACTOR ESSENTIAL OWNER/OPERATOR/PARTS/SERVICE MANUALS:
qI9P22kh.jpg

Tim Daley(
 
Maybe there are some 6 volt LED lights that do not take much power to run which will take care of your need. Be cautious on how much you spend for an outdated 6 volt system when the $$ may be better spent on 12 volt conversion. Always hard to mess with a good running tractor.
 
6 volt lights should be fine. I added two 6 volt (incandescent) lamps mounted on the top frame of my jungle jim loader. They work great to field dress my deer each year and then find my way out of the woods and to the barn. As a kid our 8N had lights - I used the lights many times to finish a job and then drive home after dark. Note, you can still buy flashlights - the 3 volt versions still work fine.

Some (not all) of the LED lights will work on 6 volts however, at a dimmed level. I am using a 12 volt yellow flashing LED light on 6 volts with good results. You would need to put two side by side, one on 6 volts and the other on 12 volts to see the difference. But this is a yellow caution light, I am not recommending using 12 volt LEDs on 6 volts for work lights. Also, not all 12 volt yellow LED caution lights will flash on 6 volts.
 
Nothing wrong with 6 volt lights. My first 8N had them and my 49 Pontiac does also. Not as much light as modern 12v bulbs, but way better than garden tractors.

cvphoto145095.jpg


cvphoto145096.jpg
 
I guess I made myself out to be more of a novice than in reality lol. Yep its a side mount and Ive read about every piece of literature there is. This is my grandfathers 8n that he farmed with and Ive overhauled the engine, clutch, lift, and the Sherman combo. Shes solid. Im pretty mechanically inclined but when it comes to electrical Id probably fry myself trying to put in a wall socket. The Dennis carpenter site is the exact headlights I am looking at too. I forgot to mention that I will be using this as a garden tractor at night if need be. My great grandfather bought about every Dearborn implement known to man and Ive restored them all to use in the garden. The one thing keeping me from switching over is Ive had people tell me itll hurt the starter and could possibly chew up your ring gear? Not sure if theres any truth to that or not but I thought Id ask the ford veterans on that. If thats not true, Ill more than likely switch over and just store the 6 volt stuff in case I want to use it later on.
Thanks for the help!
 
I had a 2N that I converted to 12V. It didn't hurt the ring gear or starter for about 30 years. YMMV
 
Beautiful Pontiac! We had a white 1952 Chieftan 2dr. Straight 8 with the visor. Moved from California to Louisiana in it in 1960. Dad traded it to a fellow for a 1966 Yamaha 50 for my brother and I in 1968. We still have the Yamaha, unfortunately the Pontiac ended up in the junk yard with a hole in the block. The 52 was replaced with a 1960 Catalina in spring of 1968.
 
I think these little tractors get a lot more personality when they have the headlamp assemblies installed. Do not use 12v bulbs, as they will be too dim on a 6V system. I have been very happy with the output of the 4019 6V bulbs (I purchase mine from NAPA). They produce plenty of light.

Colin, MN
 
The hardware will be the same, all it will cost you is a few light bulbs if you decide to change to 12volts later. You can find LED's in either voltage, but you'll likely find the six volt original equipment adequate.

Jerry
 
I have several vintage Fords with 6 volt lighting. Works fine for my needs. I like 'em original when possible.

Tractors-007.jpg
 
If you have that many implements you have been busy and have a large storage area!!! Sorry, I couldn't resist! ;^) I have done plenty of night work with a 6 volt system and lights and they put out plenty of light to work with. That's including moving a lot of snow looking through a scuffed up plastic heathouser windshield.
 
I have two Case SC tractors. The one with six volts has better lights than the one converted to twelve volts with some kind of old car lights added.
 
(quoted from post at 04:56:13 01/16/23) Maybe there are 6 volt LED headlight bulbs that do not take much power to run which will take care of your need. Be cautious on how much you spend for an outdated 6 volt system when the $$ may be better spent on 12 volt conversion. Always hard to mess with a good running tractor.
am also looking for a solution to the low amp 6V lighting for myself and this is what I have found so far. It looks like the best way to keep a more original look is to use 5 3/4 inch PAR46 semi-sealed beam housings with separate bulbs. The housings seem to be designed for H4 halogen bulbs and the amperage is very low for the LEDs.

When I regain my senses and install a 12V alternator, all I will need to replace is the bulb. This is for a 6V 2N. What came with my 12V 9N were inexpensive, black, finned, LED headlights that look totally out of place on a 9N but work very well.

There are some 6V LED headlight bulbs available, mostly 'dual filament' not that they have filaments. Many replace H4 halogen bulbs, so pretty standard hook up.
This website has been the easiest to navigate and lists a number of them: https://www.ledlight.com/led-headlight-lights.aspx
I have not bought anything from them, so I can't vouch for them. Some are positive ground, some negative and some don't care. The H4 type look like they ground through terminals on the back, not the housing, so all you need to do is keep your wiring straight and avoid the chassis ground if the bulb is negative ground.

When you search for: '5 3/4" sealed beam headlight conversion' you will find things like these:
https://www.amazon.com/IPCW-CWC-7003-Plain-Conversion-Headlight/dp/B000NZUQ56/
https://www.amazon.com/GS-Powers-Chrome-style-Acutal/dp/B07F322727/
https://www.amazon.com/JC-Performance-Conversion-Headlight-Assembly/dp/B09R6GVJKY/
https://www.amazon.com/Motorcycle-Headlight-Motorbike-1000LM-Conversion/dp/B07VWJL7C7/
If you try the links a few months from now, they will probably not work, but the search terms will. I have not bought one yet, can't recommend one over the other.
 
12V will chew up the ringgear -This is one of the many untruths involving FORD TRACTORS. The ringgear is an induction hardened part (60 Rc, I have the original blueprints with EI) and the Bendix Drive is a softer alloy; the Bendix would fail first. One if the advantages of 12V is it spins the starter motor faster which helps with a worn engine. The Starter Motor will operate on 6V or 12V; no need to get it rewound for 12V. Yeah, it's a good idea to always stash the OEM 6V components for future use or if you ever sell the tractor. OEM parts are the best resource and sought after by restorers. New stuff is mainly Cheena made junk.


Tim Daley(MI)
 
2 thoughts on the subject; 1) virtually EVERY thread on here or any of the other brand forums as well as all of my FB tractor boards that deals with electrical problems begins with; after I did a 12v conversion..., and 2) one of the ugliest things that can be done to a classic tractor is to hang an alternator where a generator belongs. Yes...I recognize that some people need 12v to run some modern equipment, and I get that. yes I also realize that a properly functioning 12v electronic ignition system requires less maintenance over time, and thus covers up a lack of maintenance in some cases. All that said, I only have 1 tractor that came from the factory with 6v system that I have converted; a Farmall Super M with a sizable overbore, and since it doesn't have compression release petcocks like my Johnnies, it can turn over pretty slow especially in cold weather so I had the generator rewound to 12v and made that conversion.
I honestly don't notice much if any difference operating at night between my 6v tractors and any 12v tractors.
 
The hardware will be the same, all it will cost you is a few light bulbs if you decide to change to 12volts later. You can find LED's in either voltage, but you'll likely find the six volt original equipment adequate.

Jerry
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top