Cold weather and alternators on my tractors (Farmall M) don't seem to mix. Tractors are all 12 volt, neg. ground, electronic ignition with one wire
alternators. Tractors have to warm up, approx. a half hour before they start charging. Generally have to move the throttle lever back and forth a few times
to start charging. I don't have this problem in warm weather. Ellis
 
Interesting. I have a few machines where you have to give them a little throttle to get the alternator excited. Then they will still charge back down at an idle. Temperature makes no difference.
 
Good reason to make the one wire a 3 wire if you have the correct version. A 3 wire will charge as soon as it gets the ignition sense and does not need to be reved up... The external voltage sense lead also helps it to start charging asap. Plus you dont have to rev' up a cold engine and get a charge indicator light. this light also helps to keep you from leaving the ignition switch on.
 
The Farmall M and Oliver 88 here that have been converted over to 12V negative ground are like that. Bump the throttle lever and they will charge until the engine is turned off.
 
Is it possible the belts are a bit loose and/or the pulleys are worn and they are slipping when cold?
 
Must have connection problems,I have one wire alternators on about 10 tractors they fire up and charge no matter the weather.Maybe your fan belt is slipping when its cold?
 
I have a six volt positive ground alternator on the super C . It needs to rev up to 1200 plus rpms to start charging, hold it there a minute or so an it will charge at idle.
I think that the newer resign pulleys on super c would be better for my set up because they are larger diameter on the fan . Anyway it one of those things just have to deal with in the tractor realm.
 
I can't remember what piece of equipment now that I had trouble with it acting like you described but I ran a 12 Guage wire from the ground source on the machine to the ground stud that is on the back of the alternator. That fixed it. I did the JD 420 that I just converted like this. It starts charging at idle. The only thing I could figure was the cold weather made the steel shrink enough to cause a poor ground.
 
I found after replacing my alternators on both
Farmall C and Jubilee I had to get the rpms past 1200 on Ford to wake up the alternator. Nothing to do with temps.. just rpms.
Same with Farmall, had to run it fast to get the alternator to charge.
 
My Super M (3-wire Delco 10SI) has gotta be bumped a bit beyond half throttle to wake it up after a cold start. And the colder it is the faster it must be spun up. However once the engine's warmed a few minutes restarts have it charging with just a blip of the throttle.

Been this way for 25+ years. I figure it's just the way it is and I live with it....
 
It depends on what regulator you have for one thing. Some are so called self exciting which is used on one wire alternators but also shows up in three wire alternators some times. There are several different regulators available and used in a Delco 10 SI alternator.

On a three wire it also depends on the feed to number one terminal on alternator. Some feed through a resistor block. Ih changed from a 25 ohm resistor on the 66 series tractors to a 10 ohm resistor due to customer complaints. Other tractors that use a lamp, the size of lamp changes excitement rpm required to start charging.

Of course, poor connection at or to number one terminal will have same effect. As for only a problem when cold I don't have a good answer.
 
I have 5+ old tractors with one wire alt. They all start to charge as soon as the engine fires.As said above,maybe loose/ worn belts and pulleys?Something is off,not right.
 
Back when we converted a couple of the tractors over to alternators they were having trouble with the one wires so we just used the 3 wire alternators and they charge right from the git go. We have a single switch for the MD and the rest all work through the key switch. H even works through the ignition switch so no forgetting and charge as soon as they start. Only one that has a problem is the 674 with the original painted red alternator it has to be run up to about 2200 to go to charging with the factory set up. I have cleaned the connections a few times and looked for a bad connection have not found any yet. I'm thinking of trying thr full ffield for an instant to see if it would charge that way. Nobody around here will open it up to charge then complain about the battery being dead. I have told them they need to open it up to charge.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top