Lanse

Well-known Member
still having major carb problems. The one on the tractor had a layer of crap in the bottom and the two off the tractor both leaked. This really sucks.

Back at it this week.
http://www.youtube.com/watch?v 4vuY_FQeNRY

C update
<object width="640" height="385"><param name="movie" value="http://www.youtube.com/v/0JcnxAKxkgo&hl=en&fs=1&color1=0xe1600f&color2=0xfebd01"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/0JcnxAKxkgo&hl=en&fs=1&color1=0xe1600f&color2=0xfebd01" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="640" height="385"></embed></object>
 
Lanse...

Some advice that I learned a long time ago working on these things - Take one project at a time.

I know that you're anxious to get your C running, but you should consider finishing the B project first. Otherwise, you run the risk of getting parts mixed up, and before you know it, you have one mass of two project tractors, and nothing gets finished. (Experience speaking here)

If you have room in another barn, move the C out of the garage (make Mom happy), finish the B with the shiny, new parts that you received from the Parts Fairy, then tackle the C. And if you think about it, the more you learn from the first project will only help you on the next one.

And before you beat on another tire with a pipe, maybe you should consider making some phone calls to DickL or one of the other gurus. They may be able to talk you through a simple leak over the phone, or at least point you in the right direction.

I've enjoyed watching your videos. Keep up the good work, and pretty soon, you'll have two nice tractors to be proud of!
 
OK, thanks

The B's parts are either on a shelf or hanging up with drying paint on them :-D
 
On any new part off the shelf (new, used or rebuilt, such as water pumps, carburetors and etc., always tighten the screws before installing. The gaskets dry over time and shrink. Tighten the screws on your new carb and it will be OK.

On the distributor, yup, replace the distributor cap, dust cover, points, condenser and rotor. The rotor just slips on. Pry it straight up and off the shaft. It just presses back on and does it's job.

Enjoy your tractors.
 
Thank You!!

Screws on the new carb are tight. If i tighten them any more i think i'll strip something.

Im ashamed to do this, but you have to learn somehow. How do replace the points and condensor??
 
Lanse,
From the brief look at that manifold, I think you should take the valve cover off and make sure that none of the valves are stuck before you turn it over and bend push rods or break rocker arms. Spray a little penetrating oil on the stems and GENTLY tap the valves with a PLASTIC hammer if they go down and POP back up you shouldn't have problems.
 
Lanse buddy, Why dont you wait until you are completely done with the B before you start on that C? Get one tractor completely done first before you start into another one. That way when you get ------ at the C you can start up the B and go for a ride to calm down.
 
Hi Lance
Just watched your "test" videos (1&2)Don't have any oil dry or cat litter? My mom would have reamed me out for getting that much oil on the floor!
Suggestion
Why don't you put an in line shut off valve on your "redneck gas tank", so you won't have to wait for all the gas to drain from the tank? Whether a carb is new or old, the reason that it would leak from the seam would seem like the valve isn't closing. My father taught me to check the float when you rebuild it, BEFORE you stick the top back on the body. Hook up your gas supply (w/ shut off valve!)see if the gas stops and starts when you move the float up and down.
I like seeing your progress (or regress, since I've pounded a few tires silly myself)so keep trying......it'll get easier........eventually!
 
I agree with the rest of the guys I think you should finish the "B" first so we can see it running right You will not see that "C" running overnight as I would assume you expect.


The "Parts Fairy" may get disturbed if you don't use parts as they were intended. I know if I were him I'd feel disappointed.

You probably pulled that distributor off without setting the timing first. Another heart ache,or hold up. We want to walk you through the process but you can't get too anxious.

I hope there wasn't a piece of gasket or dirt on the mounting area for that carb. that you may have cracked the new one.

Slow down and ask we are here.
 
Lanse, take Gary and Brians advice and just finish the B. Let the c sit with some tranny fluid in the cyls and spray the valves with a good penetrating fluid. Don't need any more bent pushrods as I don't think I have any left. Good luckcause I'm rooting for you. Probably won't see much for a few days as I go to the hospital for surgery on wednesday and will be there for 4/5 days
 
It is hard to see in the video, but did you put that IH mag on there? It wouldn't work right on the B so it won't here either. Get that dist fixed up right so it can run. Sometimes you have to tap the carb with a screwdriver handle to unstick the float.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top