I have a Marvel Schebler tsx428 carb (used on the Jubilee/NAA) that has a broken venturi. It's not too bad and I can probably glue it back together, but since this one is so brittle, I would like to purchase another one. I have looked everywhere, but I can't seem to find one. Anyone know where I can purchase one?
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
xternal_link is a possible, but be sure you get the correct one, as there are several sizes of MS carbs & likely venturi sizes.(quoted from post at 21:57:16 11/20/13) I have a Marvel Schebler tsx428 carb (used on the Jubilee/NAA) that has a broken venturi. It's not too bad and I can probably glue it back together, but since this one is so brittle, I would like to purchase another one. I have looked everywhere, but I can't seem to find one. Anyone know where I can purchase one?
Adam Davis
New User
They don"t seem to have it either. Are there any other Marvel Schebler carbs that are inner-changeable with a TSX-428? Maybe a 580? The tractor is a Golden Jubilee..
alts shows two sizes , 11/16 and 15/16 ID.(quoted from post at 06:51:02 11/21/13) They don"t seem to have it either. Are there any other Marvel Schebler carbs that are inner-changeable with a TSX-428? Maybe a 580? The tractor is a Golden Jubilee..
Adam Davis
New User
I contacted Walt's and was told they don't have a venturi for the tsx 428. Any other ideas of where I can check?
have no other ideas, but you might see if Gary in MT has a source. Just go to post by Gary (in Modern view, his e-mail is open) and ask him. Let the rest of us know if you find something.(quoted from post at 19:28:30 11/21/13) I contacted Walt's and was told they don't have a venturi for the tsx 428. Any other ideas of where I can check?
http://forums.yesterdaystractors.com/viewtopic.php?t=1080302
(quoted from post at 19:36:44 11/21/13) This guy has parts for some TSX's but seems he favors JD. Don't know what the difference in these carbs are.
Thanks Jon, I sent them an email.
(quoted from post at 06:19:21 11/22/13)(quoted from post at 19:36:44 11/21/13) This guy has parts for some TSX's but seems he favors JD. Don't know what the difference in these carbs are.
Thanks Jon, I sent them an email.
Okay, did ALOT of research online and then realized as I was working with the old venturi that there is a part number and size on the side of the old venturi. I searched and found one company that has the venturi. It's not cheap for a small piece of plastic, but I guess if you need it.
ell..............is the part number & source going to remain a secret?(quoted from post at 10:31:12 11/23/13)(quoted from post at 06:19:21 11/22/13)(quoted from post at 19:36:44 11/21/13) This guy has parts for some TSX's but seems he favors JD. Don't know what the difference in these carbs are.
Thanks Jon, I sent them an email.
Okay, did ALOT of research online and then realized as I was working with the old venturi that there is a part number and size on the side of the old venturi. I searched and found one company that has the venturi. It's not cheap for a small piece of plastic, but I guess if you need it.
gatcchelguy
Member
All Ford 134 CID motors used the same carb venturi. Shouldn't be too hard to find one.
(quoted from post at 07:55:25 11/23/13)ell..............is the part number & source going to remain a secret?(quoted from post at 10:31:12 11/23/13)(quoted from post at 06:19:21 11/22/13)(quoted from post at 19:36:44 11/21/13) This guy has parts for some TSX's but seems he favors JD. Don't know what the difference in these carbs are.
Thanks Jon, I sent them an email.
Okay, did ALOT of research online and then realized as I was working with the old venturi that there is a part number and size on the side of the old venturi. I searched and found one company that has the venturi. It's not cheap for a small piece of plastic, but I guess if you need it.
Don't know if I'm allowed to post a link here?
Britcheflee
Well-known Member
Carb parts here but do not see venturi but might be useful for those working on other carbs
http://www.carburetor-parts.com/
Lee
hanks, others will need sooner or later. Be sure to install correct side up or you might need another one. Air enters bottom/small end & exits larger/top end.(quoted from post at 12:46:14 11/23/13) Part # is 46A-240 and the site is mcdonaldcarb.
That's still cheaper than the one I found. Good deal. Glad you're gonna get it going again!It's not cheap for a small piece of plastic, but I guess if you need it.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy