Case 2 bottom plow

all_star3000

New User
Evening everybody,

I picked up a Case 2 bottom plow. It has been sitting outside for quite a few years. Could anyone tell me what model it might be? Also, what color should it be painted?

Thanks,
Sam
 
here are the pictures.

Sam

cvphoto61828.jpg


cvphoto61829.jpg


cvphoto61830.jpg


cvphoto61831.jpg
 
Connor, that is actually the same tractor I have but mine is adjustable wide front, and not in nearly as good shape(for now)
 
That plow will be an exact match for your 300. However, if your eagle hitch arms on your 300 have any side play in them do yourself a favor and remove them and the pins and take them to a machine shop and get them rebuilt. Your plow will work much better with little play in the plow and arms (like it was designed.)

Your plow is rare in its size (10") and its bottoms. You have many options with it including the hydraulic depth adjust, depth gauge wheels, and coulters. It does not look like you have the tailwheel assembly however and that is a bummer. It will still plow you will just need to find a long landside for the rear bottom.

I have pictures and info on how to convert your coulter blades and hubs over to Kinze sealed bearings setups.
 
Also, do NOT throw away those sway blocks on the plow roller. They are factory and can be hard to come by. You may not use them so either keep them clamped on the plow frame somewhere or someplace safe.
 
What are these “sway blocks” that you speak of? I will have to measure the width between the furrows, I think it is 12 inch.(pervious owner used it with a 400 I believe). Also, what exactly are scotch bottoms? Never heard of them. Only ever used a set of 2 bottom 12inch IH and a set of 3 bottom 14inch kvernlands.
 
The sway blocks are clamped on your plow towards the back of the pivot where the roller sways back and forth.

The scotch bottoms are meant for heavy sod conditions and have a very distinct point and long moldboards that curve over much more than the other bottoms. You cannot get the points (shares) or moldboards for them anymore.
 
Also, I would recommend getting a manual for that plow. If you are going to be using it on a 311 (rock island tractor) them your lower lift pins will need to be raised to the upper holes for best operating results.
 
Connor, if these are the scotch bottoms you are referring to, i have seen a few of them around on different plows. They seem to be common on old plows in my area(southern Quebec). The IH plow i have used in the past for plowing matches had them.

This plow also seems to be a 12 inch. The pins seem to be threaded if i am not mistaken.

I will have to look on ebay for the book for them.

What are the plastic covers on your plows? Never seen that before. Could you send me more pictures of your plows?

The info on changing the bearings would be nice.

Thanks

mvphoto64513.jpg


mvphoto64514.jpg


mvphoto64515.jpg
 
The pins are threaded and might need to be heated up to remove. The Ops manual should have everything you need to get it set right for your tractor. You were right on them being 12" spacing.
The poly moldboard covers were made by a company called PolyTech in Georgia. I will include a link for them. The call them CaseIH EX16 but they are really J.I. Case EX16s. The will fit on EX14s as well with
a little over overhang at the edge of the moldboard.

Also, If you are looking for moldboard extensions for the EX moldboards John Deere ones are still available and will fit without modification. I have a pair on mine.

MayWes in Minnesota also offers poly moldboard covers. The really do pull easier and dont cake up with mud/dirt.


cvphoto61964.jpg

EX16
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top