Case 300 or 300B

I can't seem to find any info on the brakes, where they are, how they work, how to check them, etc. I have a JI Case service manual copy for 300, 300B and 400B, no brake section. I think my version is a 311 (wheels), not sure but looks like it in the manual. The brakes don't work and I can't find a repair path. Please help.
 
Brakes work off the transmission differential shafts so are in transmission section in manuals.

CaseIH service manual Rac 9-92002, 300 300B 400B tractors. Brakes are Group E - Transmission, Section VIII, Differential Brakes, Pages E-29 & E-30.

Joe
 
The brakes are located in the square shaped housings just infront of the rear axle housings. You need to remove the floor boards and remove the 4 nuts with a 3/4 wrench. Also remove the adjusting nuts connecting the linkage.Pull the covers and everything is there. If discs ar not worn badly, just clean them and deglaze them with sand paper. The expanding discs are held together with springs. Remove them and one of the sholder bolts on the straps to seperate them. 3 balls will fall out. If they are in poor condition replace them. The socket shaped ramps should be cleaned up with a small rotary brush or a die grinder if rough. The balls should roll up the ramps smoothly expanding the discs apart when pulling on the adjusting rod.If there is oil leaking in to the bake housings you will have to replace the seals in the bearing quills. This procedure was discussed extensivly last weekend on this forum.
 
I hope I did this right... Here is a picture of the brakes on the 300 Series. This picture is from the Case/IH online parts book.
The brake housings are located behind where your feet rest on the floor boards/foot rests. There are 4, 5/8" studs holding the housing to the differential case. Floor boards need to be removed to get them off. There are also 2 large, flathead machine screws, with like #4 Phillips drive, that need to be removed, to get the bearing carrier plate off. More than likely, the seals are bad, and need replaced. They are located in the carrier plate, and it needs to be removed to replace them. I replaced those screws with a similar screw, but with a internal hex drive. Makes it a whole lot easier to put back, or if it needs to be done again.
I just replaced mine last week in my 310B. Not a bad job, just tricky getting the new seals in, without ruining them. I posted last week, an idea I found from another member here, on another site. Look for "brake seal saver idea", or something lke that. Basically, you clean the differential shaft up ral good, and wrap the brake/bull pinion gear/shaft with electrical tape, as a shim to get the seal over the splines, and not turn it inside out, or damage the lip on the seal...
If the brake discs aren't worn too bad, they may be cleaned up, roughed up, and used again. I tried an idea from another old Case guy on mine. He called it "buring the oil off the discs. I cleaned them up the best I could with brake cleaner. Then took a propane torch, and just warmed them enough to literally boil the oil out of the discs. I couldn't believe how much came out... This was done outside, and a good breeze going. Sure don't want to breathe those fumes!! I also roughed them up with a medium roloc disc on my air angle die grinder. Worked real well, and saved a lot of hand sanding..!!
Yesterday was the first day for it out of the shop, and the brakes worked great..!!
I also posted a site to get seals a lot cheaper than NAPA or like Motion Indutries. Less then $10.00 ea., versus $15.00 to $17.00 at the other places, and it is the same SKF/CR seal..., but takes about a week to get them.
Sorry to be so long winded, but hope this helps...
 
Hoss54, roughing them up with a grinder will likely leave you with uneven disks. Here's what I did and it worked very good.

Take a whole sheet of 150 grit sand paper. Put it down on a flat surface, shop floor, workbench top, etc. Place the disk on the sand paper and make about 10-12 revolutions with the disk on the sheet, flip it over and do the other side, and viola, a roughed up perfectly flat disk.

Jim
 
These are just the roloc pads you use to clean off gasket surfaces... Just kept it moving, and it seemed to do a real nice job..

Yep, I've done the sandpaper thing numerous times on our IH's...
 
Didn't catch the roloc in the post, I was reading grinding disk in my mind. Yes, I believe that the roloc pads will work well.

I don't keep these in my shop inventory, but I always have packages of sand paper sheets so that is what I first picked up to try.

Jim
 
I've gotten myself spoiled with little amenitie's like that. Wouldn't be without one now.. Sure makes cleanup a breeze!!
Guess the secret is to having a low CFM angle grinder, to save running the compressor much. But they are sweet.. And you can find some deals on pads on Epay, if you keep an eye on them...
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top