Case Taskforce 700 Trencher/Backhoe

JeffEck

New User
I recently purchased this machine to use on our house project. I have searched and searched for an operator's manual and ordered one on eBay that was in Brittian. I have been waiting for the manual for some time now.... On Friday I was working with the backhoe and went to move the machine when I broke a track and damaged the idler sprocket. Dad was able to tig the sprocket using nickel rod with heat and we repaired the track, but I cannot for the life of me figure out how to tighten the tracks so this doesn't happen again. I found it has a grease cylinder to extend and a pair of bolts that seem to be the part for the adjustment, but one cylinder just leaks grease and the other does nothing at all. Has anyone ever worked with a TF300 or TF700 and know what I am doing wrong? From my research, the same tracks were used on the TF300 and TF700 but I am not sure on other models. It's crazy that this machine was built here in Wichita Kansas but I can only get a manual from Europe.


mvphoto85196.jpg


mvphoto85197.jpg


mvphoto85198.jpg


mvphoto85199.jpg


mvphoto85200.jpg


mvphoto85201.jpg

[/img:23e38cee5a]
 

Have you tried talking to a Case dealer to see if they can get a manual?

If it works below is a link can click on to go to the Davis TaskForce 700 parts book on line at MyCNHi US Store, in the Case Construction Equipment Group.

https://www.mycnhistore.com/us/en/c...9FCE-005056875BD6&isSnFilterEnabled=false

It shows hydraulic (grease) adjusters so it would appear you have blown seals in the one that leaks grease and if the grease gun just comes up hard when you try the other one, it may be rusted in place. The parts breakdown looks like the entire track frame may slide for adjustment. Assuming you have looked it over to see if there are bolts (in slots) to loosen before adjusting, it may be at the end of its travel, meaning the tracks are worn out.
 
I found the grease cylinders were intended to move the differential back to tighten the tracks. I used a porta power and have successfully tightened the tracks. Once I understood what it was supposed to do, I just worked around it... At some point when I get to overhauling the motor I will replace those cylinders with new ones or change the design to use hydraulic power to do the same...
 
You won't need to work around it just jerk the cylinders out and put new seals in them and use the
grease, adjusting the tracks is not something you are going to do very often.
 
When you go to getting into overhauling the engine you may decide to find another unit. What parts
that are out there for those engines are somewhat expensive.... just plain high
 
Let me add that you should be kind to the hydraulic stack valve bank on the hoe. It's a Cessna, and replacement parts are NLA... You can round up seals and such, but forget hardware.

The Davis line was bought by Case... Then Case sold its trencher line to Aztec Underground. They have since sold it off to someone else, so support is tough to find. The hoe is ether a D-100, or perhaps a D-130. You will have no trouble finding parts breakouts on those as they put those hoes on anything they could for decades... They're good solid machines, with the only real weakness being their very narrow outrigger footprint. That may be less of an issue with your heavier machine than with my little Case 646.
 
Thank you for the heads up. Any suggestion on the hydraulic oil? The conveyor's speed adjustment valve leaks quite a bit and I didn't notice until I had left plenty of oil on the ground.
 
No idea what your machine was speced for. My 646 was designed around 15w-40 as the hydraulic fluid for the whole machine. I wouldn't call that a "normal" choice, so I wouldn't expect that to apply to your system.

FYI, on a lark, I just checked the Case Construction site. You can get a parts breakout of the 700 there.
Under the Parts Books area, just type "Task" after selecting Model from the dropdown. They have the 700, and the 1000 with full parts breakouts.
 
(quoted from post at 23:41:49 11/30/21) I do have a ORIGINAL Operator manual for sale for the TF 700 if needed and I the TF 300 is the same I have a parts manual and a
service manual for the TF 300 for sale. my e mail is [email protected]

I sent you an email on the manual.
 
I broke my transmission housing a month or so ago. Ill
post some before and after pics of the repair goes well.
Can anyone in here confirm the TF 300 and TF 700 have
the same track system..? I might have a line on a tf 300
for a parts machine if my repair doesnt go well on my TC
700.
 
I have both a TF300 and TF700 now and I believe the tracks are different. I'll go take some photos and looks closer after the sun comes up and post back here.
 
(quoted from post at 10:01:50 11/28/21)
Have you tried talking to a Case dealer to see if they can get a manual?

If it works below is a link can click on to go to the Davis TaskForce 700 parts book on line at MyCNHi US Store, in the Case Construction Equipment Group.

https://www.mycnhistore.com/us/en/c...9FCE-005056875BD6&isSnFilterEnabled=false

It shows hydraulic (grease) adjusters so it would appear you have blown seals in the one that leaks grease and if the grease gun just comes up hard when you try the other one, it may be rusted in place. The parts breakdown looks like the entire track frame may slide for adjustment. Assuming you have looked it over to see if there are bolts (in slots) to loosen before adjusting, it may be at the end of its travel, meaning the tracks are worn out.
 

I have a similar machine, with no decals to tell me what model it is. It doesn't have a trencher attachment. It has a 6-way hydraulic dozer blade on the front and a Davis 100 backhoe on the back. It has a Wisconsin 4-cylinder engine. Unfortunately, somebody removed the steering brake levers, and I'm having trouble figuring out how to fabricate a replacement.

The Case manual post Jim sent gave me some ideas, but without knowing if my machine is a TF 700 or some other model, I'm not sure.
mvphoto107001.jpg


mvphoto107002.jpg
 
(quoted from post at 09:38:24 06/24/23)
I have a similar machine, with no decals to tell me what model it is. It doesn't have a trencher attachment. It has a 6-way hydraulic dozer blade on the front and a Davis 100 backhoe on the back. It has a Wisconsin 4-cylinder engine. Unfortunately, somebody removed the steering brake levers, and I'm having trouble figuring out how to fabricate a replacement.

The Case manual post Jim sent gave me some ideas, but without knowing if my machine is a TF 700 or some other model, I'm not sure.
mvphoto107001.jpg


mvphoto107002.jpg

What is your question bud? I don't know what model you have, but I can take photos of mine if you want me to show you different parts to help with your issues...
 
(quoted from post at 13:24:36 06/25/23)
(quoted from post at 09:38:24 06/24/23)
I have a similar machine, with no decals to tell me what model it is. It doesn't have a trencher attachment. It has a 6-way hydraulic dozer blade on the front and a Davis 100 backhoe on the back. It has a Wisconsin 4-cylinder engine. Unfortunately, somebody removed the steering brake levers, and I'm having trouble figuring out how to fabricate a replacement.

The Case manual post Jim sent gave me some ideas, but without knowing if my machine is a TF 700 or some other model, I'm not sure.
mvphoto107001.jpg


mvphoto107002.jpg

What is your question bud? I don't know what model you have, but I can take photos of mine if you want me to show you different parts to help with your issues...

Please be patient while I learn how to use this website. I'm attaching some photos of the chain drive for the tracks. There are two hydraulic motors mounted one above the other and one drives each side of the tracks. There are two slots above the chain on each side. I wonder if there is supposed to be a shaft that goes through those slots with a sprocket that would put pressure on the chain when the (missing) brake lever was pulled?
mvphoto107069.jpg


mvphoto107071.jpg


mvphoto107073.jpg
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top