Chain saw chains

37 chief

Well-known Member
I have a Husqvarna rancher 55 chain saw. Over the years I have gone through a lot of chains. Anyone tried a carbide tooth saw chain? I know carbide will not lase forever, especially if I hit something solid. Then it will probably cost more to regrind. Any thoughts? Stan
 
Are not those carbide chains the ones the fire department use for their saws on steel and such? Friend of ours bought one for a saw. Far as I know he has not sharpened it yet that was a couple of years ago. You will pay dearly for it though according to him.
 

A friend went that route. Thought he'd never have to sharpen a chain again. He found out that carbide chain, at least what he got, doesn't cut as well as traditional chain (took a lot more power out of the saw)due to different geometry on the tooth and that he had to get is ground at a shop to sharpen it. He got through about 3 sharpenings and hung the chain on the wall where it sit to this day. IMO it's a specialized product for specific applications and not a general purpose chain at all.
 
I bought one several years ago when I got tired of constantly changing chains, sharpening chains, etc. Bought a carbide one, put it on the saw, and it's still on there, works great. Never touched it except for an occasional retension. Every time I use that saw it goes through logs like butter and if I hit a nail or accidentally hit the ground with it it doesn't care. Get a carbide tip chain and never look back. Just my $.02. Brian
 

Carbide is brittle. It will tend to break more than wear. It will not get as sharp as steel because that thin little edge tends to chip off after a couple of uses. It is also expensive in comparison to a non-carbide chain.

But, it will cut through nails and other contamination found sometimes in wood, and it will not immediately get dull if you hit the ground or a rock with it.

Ultimately, you will have to be the judge as to whether it will work for you. As you can see, there are varied levels of success with it.
 
If I remember right Traditional Farmer has some experience with carbide chains and had some suggestions. He can add some first hand info.
 
My take is that the Carbide chains can help, but may not be a cost saving as much as a time saving. That said, supporting material being cut, debarking rough textured logs that have been horizontal for years, running quality bar oil in amounts that show up on the next log over, and not running dull chain are value added policies. A worn bar/sprocket is another chain destroying element. Cutting dead standing oak in Arizona's Coconino National Forest we ran the same cahin with a touchup sharpening at noon, and after we stopped. Chains lasted through 8 full cord. Jim
 
I don't know about time saving.

In Project Farm's test of various chainsaw chains (linked above), carbide was one of the SLOWEST cutting chains in the mix, if not the slowest.

You also can't sharpen it in a few minutes with a simple file.

You're better off with semi-chisel or even full chisel chain, being more careful when you're sawing, and learning how to sharpen your chains.
 
(quoted from post at 14:33:54 01/12/21) I don't know about time saving.

In Project Farm's test of various chainsaw chains (linked above), carbide was one of the SLOWEST cutting chains in the mix, if not the slowest.

You also can't sharpen it in a few minutes with a simple file.

You're better off with semi-chisel or even full chisel chain, being more careful when you're sawing, and learning how to sharpen your chains.


The other issue is you're using a dinky little saw to start with. Carbide tooth geometry isn't the same as a standard chain. You are going to loose a good deal of available HP to that, like running a dull chain. Get a good file guide and learn to use it. It's not hard at all.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top