concrete question

Bob N.Y.

Well-known Member
Location
Norway, N.Y.
I know that water combines chemically with cement to form concrete. If someone were to mix 800 pounds of sacrete with the appropriate amount of water, would the weight of the water still be present after the concrete has cured? Thanks in advance.
 
no---water water is used in the hydration process is quite small and the extra evaporates--when you design a concrete mix the sum of the aggregates and water always exceeds the 150 pcf average of dry cocrete
 
I would take a guess at that and say not 100%. I have poured a lot of 10x16 slabs around the barn using a hand mixer. I fill a 55 gallon drum with water and set it next to the mixer and it is mostly empty when I am done. That is a lot of weight. But my belief is a lot of that precipitates out in the curing process. Still concrete seems to take up water to some extent. I think some of that weight has to still be there. Not very scientific, but I bet a slab weighs more than the dry ingredients.
 
I have designed a number of concrete mixes and the sum of the batch weights per cubic yard has always been less than the weighed density weight of the 28 day concrete cylinders that we tested--of course light weight concrete is a special case but i never designed or tested them
 
My thoughts are that most of the water evaporates in the first couple of weeks. Then you get into the moisture density of your crete . Kinda like sawn lumber vs. kiln dried. Some of the weight stays, but a WAG is 10%.
 
its generally assumed in the industry that the concrete is still utilizing the moisture for 28 days to develops its specified strength
 
The amount of water that it takes to create the chemical bond (cure) is less than what it takes to make it pour. The excess will soak out and evaporate at some point. It is important to note that concrete does not "dry", it cures.
 
You need much more water in the mix than is required to react with the cement to get a workable mix. That excess evaporates out, leaving the cured concrete less dense than the mix. The more water, the less dense, which is why it's important to use no more water in the mix than is absolutely necessary. Note also that concrete shrinks as it cures, which is why you need control joints in a large slab.

Doing a bit of googling, it's hard to find a definitive answer, but it seems wet concrete weighs around 3700 lbs/yd<sup>3</sup>, while cured concrete is about 3600 lbs/yd<sup>3</sup>.
Weight of concrete
 
There is no set weight for a yard of concrete,since sand and gravel vary considerably in weight.Some lightweight aggregates makes for some very light concrete,think
about the lightest we poured was under 3,000 lbs/yd up to about 4400 lbs/yard.The more water the more shrinkage,the more cracking.To accurately get a yard for a mix all the variables have to be taken into account.I've taken hundreds,probably thousands, of aggregate weights and moisture tests on aggregates,weights of aggregates can vary out of the same quarry when they start a new vein.Quarry would give us a heads up when that happened so we could adjust mix designs.
 
The water eventually goes away. When we break up old concrete it is dusty. I don't equate water and dust being in the same place.
 
(quoted from post at 12:45:09 01/11/21)

Doing a bit of googling, it's hard to find a definitive answer, but it seems wet concrete weighs around 3700 lbs/yd&lt;sup&gt;3&lt;/sup&gt;, while cured concrete is about 3600 lbs/yd

Mark, that was an interesting site.....I never thought about the amount of water to mix a yard of concrete being so little.
We can prove that some of the water evaporates if we cover a newly poured slab with a vapor barrier and view the captured water.
 
A cubic yard of wet concrete is about 3700 lbs. A cubic yard of dry concrete is about 3600 lbs. Most of the water is incorporated into the concrete, but a little does evaporate. Both weights are approximate, and vary with the type of sand and gravel used.
weight of concrete
 
According to my SIL, who spent quite a bit of time in college weighing and breaking concrete, the answer is YES. The water never leaves the mix. Water is the reason that concrete will Pop chunks out when overheated with a torch for example.
 
As a general contractor, I've built a lot of concrete tilt-up flex space buildings. Some of the buildings or parts of the buildings would not be rented or have a tenant improvement for a year or two. Unless some ventilation was provided the inside of the roof / insulation would be so wet from concrete curing that it would actually "rain" inside. We used to install roof vents for just that purpose. If occupied with doors opening and closing so some air movement you wouldn't notice it.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top