Dear barney

SVcummins

Well-known Member
.
cvphoto102396.png
 
I like.
Someday I'll post pics of my straps.
I attach 3/8 G70 chain to my strap ends to prevent straps from coming in contact with any metal on tractor. May not be DOT approved, but it works better than any plastic guards.
Say hi to Barney.
 
You can buy straps with chain on the end . I didnt want to use chain because I didnt want to ruin the sickle sections so I used a strap with the lid to protect the strap and the machine . Barneys problem is he isnt smart enough to use his own brain without the ytdot handbook
cvphoto102401.jpg
 
Niehbor gave me a roll of fire hose. It works real well. that is some tuff stuff. Havn't cut it yet. RB
 
Barney is so busy hes even had to open a few new divisions and hire more deputies
cvphoto102406.jpg


cvphoto102407.jpg


cvphoto102408.jpg


https://www.yesterdaystractors.com/cvphotos/cvphoto102409.
<img src=https://www.yesterdaystractors.com/cvphotos/cvphoto102410.jpg

cvphoto102411.jpg
 
Had to see it barney would approve the strap protector or deem it illegal and endangering little old women everywhere.
 
Ill have to see if the fire department here has any old hoses . I dont use straps as a rule if theres a chance that it might get cut . Straps were the best way to tie the header down without damaging the header. I need to add some d rings to the header cart and weld some hooks or d rings to the header
 
I used to get old truck wheel liners that fit between the wheel and tube, cut them 18 inches long and use them between the straps or chains and sharp edges. Back in the 90's when I was running the country with my step deck trailer you could get them free at most truck stop tire shops, good thick rubber that lasts a long time.
 

While it works good in many applications, fire hose wouldn't save sickle sections from chains, your lid was the better choice, even if not great.

Sections of bias ply car/light truck tires give more cushioning than fire hose, but bias ply are getting harder to find.

You're right, dedicated tie down points, like adding D rings to the cart and header would be best. One of those projects we remember when we need them, but something else has top priority when we don't.
 
SV,
You can buy straps with chain on the end

Tell Barney someone stolid my idea.

I should have patented my idea.
 

Speaking as a former DOT cop, looks good to me. I've been out of it for 12 years now, but I don't recall anything that said an edge protector had to be a boughten item. Used to see a lot of them that were made op of belting screwed to 2x2's about 6" wide. Worked good.
 
I have a couple of pieces of angle iron I put over the knife bar to keep the strap out of the sections and off the guards. Works good and has not cut the strap either. A piece of square tubing would work better with the rounded corner.
 


Yesterday I came across a length of 1.75 fire hose at the fire station that failed testing last spring and is in the way. I am going to cut off the couplings and a few feet to put over chains and the rest is going to the transfer station.
 
A couple of days ago I went with my son to haul a heavy duty forklift from the south shop six miles to the north shop. It probably weighed 10,000 pounds. All he had to tie it down with was two 2" ratchet straps. One went across the foot platform and the other went around the hitch pin. We took lonely county roads home but barney would have had a laughing fit if he would have stopped us.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top