Engine stand

SVcummins

Well-known Member
Anyone have one of these ?
cvphoto65856.png

One tone engine stand
 
NO, i don't, but that looks like it's built on the premise of the hoist,Looks to narrow and not enough support on the business end, there no need for it to be that narrow, where the weight is going to be!
 
2 of them. Wouldn't be without 1. Have a 6 cyl. wakesha on one and a 4 cyl deere on the other one. Waiting on a crank for the deere. Hopefully be done with it this week. RB
 
What's it rated for? Most of these engine stands are flimsy and will collapse under the weight of a tractor engine even if they're rated for it.

I would go for the next size larger than you think you need, for that reason alone.
 
This is mine. It's a Harbor Freight special, heavier of the ones they offer. So far it's only had a little 4 cylinder on it but it will probably have a 6 cylinder on it this winter. My only complaint is that it's hard to spin the block over.
cvphoto65863.jpg
 
Never had one to use. I would guess for that truck block you might want one that holds both ends to keep the leverage down or use 2 one on each end.
 
Way better than mine. Tee design , get heavy engine like Fordson ,go to rotate it outside on sloping driveway it will possibly tip over. Don’t want that ,need to people for sure transporting it .
 

I like this type better.









https://www.northerntool.com/shop/tools/category_automotive+engine-hoists-stands+engine-stands


I like this one also.

https://www.northerntool.com/shop/tools/product_200641860_200641860

I used a 1k on my ford diesel it weighs 1k
 
Yes, just like that, and a single front bar one too. The two bar is much more stable, but I wouldn't use it on your 5.9 engine. You really need one like the heavy OTC with the gearbox rotator.
 
like said fine for a light car engine Worthless for a heavy engine and a accident waiting to happen if you try it,, I bought the heaviest built one I could find on hand in town worked "ok" on the 360 from my pickup but about had a bad thing happen when I was using it to hold the 40 hp gas engine from my 530 CASE and I was rotating it,, no way would I want a 5.9 on it
 
also ran across pics of the Du Al cylinder tool
cvphoto65885.jpg


cvphoto65886.jpg


cvphoto65887.jpg

not the best shots to explains how it works, there are two sizes of the spanner needed for in and outer nuts they have,
 
I built this stand a couple years back. I basically copied the commercial built 6000 lb stands.
cvphoto65893.jpg

I needed to hang this John Deere 6 cyl on it.
cvphoto65894.jpg

I've done a 6.5 diesel with it since, and currently have a 4 cyl Perkins on it.

I'd assume your 5.9 would be similar to that deere engine, HEAVY... The worst part is rotating them on a small stand like that. There's just no way to balance them. The deere actually mounted on the side of the block, which was kind of slick. No mount in the way of installing the rear main seal.

I had most all of the material laying around, so I really only had about $100 and my time in building it.
 
I only work on my own engines so I don't need a stand very often. I have one like that I've used maybe 4 times in the last 30 years and has worked fine for me.
 
I built my own years ago, similar to the ones shown here.

It's held up under 454 big block Chevies OK. Haven't had reason to put anything heavier on it.
 
For the engine in progress, you need twice that strength. It will fold. If you have a 3 point hitch tractor to spare, make a plate to fit that with holes to match the bell housing. then you have mobility and up and down. If you added a rotator to that it would be sweet. Remember that the crank shaft is not the center of gravity. so a locking mechanism is needed. Jim
 

two comments from using them..

IF... you mount the engine with the rear arms CENTERED,,, it will then spin over easier... if you just mount the engine in the lowered position, it will be very very hard to spin over.

AND,,, if you look at the entended legs, and where the wheels are mounted on the floor.... those wheels are the center of gravity point as to where it will flip over... so the engine would have to stick out more than half of its length past those front wheels... That would mean your engine would need to be nearly 7 feet long to flip...merly sticking out 6 inches or a foot past the those wheels, with 3 feet plus on the other side will not tip it.


And yes, you dont use this on an incline or rough floor.. Actually you probably should not move the stand once an engine is mounted.

getting the block centered, and then adding the heads to it, can make it harder to spin, so I always add the heads last thing in the assembly process. I always use the long pipe (jack handle) to spin the engine. there is a place to store the pipe on the stand.
 
Here’s my big stand I build quite a few years ago. I also use an OTC stand as a pattern only with my twists put into it. The big mounting plate is the same as the OTC then if I need to buy an adapter it’ll fit my stand. I have been making all the adapters so far. This is an M farmall engine on it now. I’ve had a 4020 diesel on it and some big six IHC engines.
cvphoto65913.jpg

I don’t even take the small stand out anymore after I built this adapter.
cvphoto65914.jpg
 
I bought one like that to do the C263 gas in my 560. Legs are not long enough for a six cylinder and not heavy enough even though rated a 2000.Bent it and had to support with my engine hoist.
 
if you can see the one side has about a 3" extension that is needed to reach inside the tube to remove the inside gland,, so a normal one will pull the outside but I doubt it will on the inside
 
Hey Tim, I was going to brag on the one I made in shop class about 60 yrs. ago.....after seeing yours, I think I'll pass.
 
This one does work good,, the down side is that it needs latched to keep it in place..the final drive is 8-1 ratio so it does turn easy.I have an old ISO 404 bell housing bolted onto it for my Deere engines,which is what i do the most of,
 
(quoted from post at 11:13:50 12/06/20) would'nt be cheaper in the long run just by a rebuilt or used engine?

Grizz, do you want to get your old phart card pulled and kicked off the forum??? We don't do cheaper and we don't buy rebuilt we do it ourselves no mattter how much more it costs. Now report back whe you have washed your mouth out!!!
 
A reman engine is 6000.00$ and I’ve checked on several uses engines and they are 3000,00 I can rebuild this one and have a new engine for 3000.00
 
I think I will improve my table for the amount of engines I do that’s how i learned to do them and it works pretty good because you can get to both sides of the engine without rotating anything
 
You have to remember it has to hold up while you are lugging away at the engine with a torque wrench. I doubt if that stand will break but it could bend so the engine will be pointing to the ground. I made my stand based on an irrigation pivot gearbox. Had a 619 Deere engine on it bolted sideways and the stand held it ok but i still put extra support under the engine when i was torquing.
 
I have that that you can turn the engine up and on its side. The blue bracket is made for B or C series Cummins. They will hold up to a K19. If you were closer you could use it. They been back of the shop for 20 years.
cvphoto66013.jpg


cvphoto66014.jpg

E
 
not sure what year your dealing with but E-bay has rebuilt units from 3400 to 3700 just a thought plug and play
 
I wouldn’t trust an eBay reman as far as I could throw it and that’s still a thousand dollars more than I can do it myself for . An complete engine kit is a thousand dollars a complete rebuild on the head is 500$ and 500$ for machine work then you know what’s done . Bubbas reman and chop shop probably consists of a scotch brite crankshaft polish and ball hone on the cylinders a set of bearing shells maybe and two cans off rustoleum new engine in a can .
 
Hey SV, I'll give you one kind of like the one JayinNY posted, but beefier. I'm in Idaho Falls. Won't cost you more than a trip up here to collect it. E-mail me and I'll send some pics...
Cheers,
Jeff Brough
 
I really started thinking on a used engine but they want as much as I can rebuild one for and the only ones they can come up with is a cummins 53 block and I will not try that ever again there are 5 people that have those right in my general area like 40 mile radius that have cracked all worked but not abused everyone has cracked around 200 to 220,000 miles
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top