got hubs off, problems continue

tn8n

Member
So, with the help of everyone who replied to my earlier post, I got the hubs off. I did have a replacement hub with only two retaining screws, both of which were missing. A BFH did the trick, and with no damage to the hub. I was praying I'd find something easy like a broken retracting spring, but of course not! It's in fine shape.

In case you missed my other post, my right side brake is not retracting when the pedal is released. Right now, with the brake shoes removed, it is so hard to push the pedal down it is actually bending the shaft down at an angle instead of rotating. I know it won't retract without the shoe assembly installed, but it's still just as hard to depress and it's quite hard to pull it back up.

I have thoroughly cleaned all the brake components. The problem seems like it could only be inside the center housing, where the brake camshaft enters it, or at the point where it enters, if there is a bearing or bushing there.

I have studied all the diagrams in the I&T manual, and so far all I have really been able to deduce is that the camshaft has a ball on the end. I can't see any kind of bushing where it passes through the housing, and I can't find a diagram of the "socket" that the ball would fit into. If I remove the arm with the pawl(where it engages with the sector on the housing)on it, will the camshaft slide out? I also thought about removing the inspection plate with the transmission dipstick on it, it seems to be close enough to let you see the ball/socket.

By the way, Dell, from my last post:
"Many times to break the RUST BOND, you haffta loosen the large nut and drive in figger-8's in driveway. ........HTH, nutless Dell"

What does HTH mean? Hope this helps?
 
Well, I'm totally confused now......which isn't unusual.....but what are you talking about? I thought you were trying to remove the brake drums, not the hubs.
50 Tips
 
The part in the top picture w/ the studs is the hub.

The drum is on the other side of the backing plate in the bottom picture.

So, which part were you trying to remove, the hub or the drum?
RearHub-1.jpg

August232009003.jpg
 
(quoted from post at 06:23:06 10/29/11) So, with the help of everyone who replied to my earlier post, I got the hubs off. I did have a replacement hub with only two retaining screws, both of which were missing. A BFH did the trick, and with no damage to the hub. I was praying I'd find something easy like a broken retracting spring, but of course not! It's in fine shape.

In case you missed my other post, my right side brake is not retracting when the pedal is released. Right now, with the brake shoes removed, it is so hard to push the pedal down it is actually bending the shaft down at an angle instead of rotating. I know it won't retract without the shoe assembly installed, but it's still just as hard to depress and it's quite hard to pull it back up.

I have thoroughly cleaned all the brake components. The problem seems like it could only be inside the center housing, where the brake camshaft enters it, or at the point where it enters, if there is a bearing or bushing there.

I have studied all the diagrams in the I&T manual, and so far all I have really been able to deduce is that the camshaft has a ball on the end. I can't see any kind of bushing where it passes through the housing, and I can't find a diagram of the "socket" that the ball would fit into. If I remove the arm with the pawl(where it engages with the sector on the housing)on it, will the camshaft slide out? I also thought about removing the inspection plate with the transmission dipstick on it, it seems to be close enough to let you see the ball/socket.

By the way, Dell, from my last post:
"Many times to break the RUST BOND, you haffta loosen the large nut and drive in figger-8's in driveway. ........HTH, nutless Dell"

What does HTH mean? Hope this helps?

The ball end goes into a bushing and should just slide out.
 
Yeah, sorry about that. I posted my message and then headed over here to my parent's house, and about halfway here I realized I had used the word "hubs" instead of "drums!" Soon as I got here I jumped online to correct myself. So yes, I meant drums. Brake drums. The right side brake drum.
 
I'm not sure what your problem is. The brake shaft should rotate easily, it rests in a socket on the rear/hydraulic housing, and pokes through a hole in brake backing plate, it is supported between the the two brake shoes and held in place by the springs. Nothing there that should stop it from working

Unless something is grossly out of place it should work easily. Tell us more.

BTW (By the Way) HTH means "hope that helps"
 
Did you look very closely at the back of the brake support plate 8n2212b? Sometimes the nub on the back of it will break loose from the plate itself and bind on the brake shaft and cause these problems.It is where that brake shaft rests on after it enters through the backing plate.
 
I know this sounds like a really dumb question but you mention that you can't move the brake peddle. Are you sure that the brake lock did not accidentally engage? It is easy to accidentally push it in exactly the right way to lock the peddle. I know because I did it one time and $%^# myself when I found the problem. Like I said, dumb question but sometime it is something really easy like that. Gene
 
(quoted from post at 16:42:04 10/28/11) I'm not sure what your problem is. The brake shaft should rotate easily, it rests in a socket on the rear/hydraulic housing, and pokes through a hole in brake backing plate, it is supported between the the two brake shoes and held in place by the springs. Nothing there that should stop it from working

Unless something is grossly out of place it should work easily. Tell us more.

BTW (By the Way) HTH means "hope that helps"

I'm not sure if you mean I haven't described it well enough and you can't understand what my problem is, or you understand but you can't figure out what would be causing the problem.

The whole problem here is that the right brake pedal is very hard to depress, and does not return when released. I thought the retracting spring was broken, but it was not. I removed the wheel, brake drum, and shoe assembly. Even with the shoe assembly removed, it is exactly the same. (I know it won't retract without shoes and spring!) It is so hard to push the pedal down, it's flexing the shaft downward as it rotates. I pull it back up and it's hard to lift. I'd say it takes about 20 lbs of force to lift it back up.

so...... obviously if is still stiff with the shoes removed, the problem must be in either the ball and socket in the center housing, where the shaft enters it or on the other end where it passes through the back plate. my question was how does it come out of the center housing, i can't find a picture or diagram anywhere. r geiger says it should slide out so i solved that. i'll look at the other end for a broken nub on the back of the anchor plate.

to get the shaft out of the center housing do you have to remove the little arm, the one that has a pawl on it which engages the sector on the housing?
 
(quoted from post at 10:38:17 10/29/11)
(quoted from post at 16:42:04 10/28/11) I'm not sure what your problem is. The brake shaft should rotate easily, it rests in a socket on the rear/hydraulic housing, and pokes through a hole in brake backing plate, it is supported between the the two brake shoes and held in place by the springs. Nothing there that should stop it from working

Unless something is grossly out of place it should work easily. Tell us more.

BTW (By the Way) HTH means "hope that helps"

I'm not sure if you mean I haven't described it well enough and you can't understand what my problem is, or you understand but you can't figure out what would be causing the problem.

The whole problem here is that the right brake pedal is very hard to depress, and does not return when released. I thought the retracting spring was broken, but it was not. I removed the wheel, brake drum, and shoe assembly. Even with the shoe assembly removed, it is exactly the same. (I know it won't retract without shoes and spring!) It is so hard to push the pedal down, it's flexing the shaft downward as it rotates. I pull it back up and it's hard to lift. I'd say it takes about 20 lbs of force to lift it back up.

so...... obviously if is still stiff with the shoes removed, the problem must be in either the ball and socket in the center housing, where the shaft enters it or on the other end where it passes through the back plate. my question was how does it come out of the center housing, i can't find a picture or diagram anywhere. r geiger says it should slide out so i solved that. i'll look at the other end for a broken nub on the back of the anchor plate.

to get the shaft out of the center housing do you have to remove the little arm, the one that has a pawl on it which engages the sector on the housing?

It should just pull without having to emove the parking braake arm. Look at it< do you see any thinkg the arm will hit? I don't believe there is. I went out and looked, was going to take a picture but batteis were low. Mine is pretty loose in bushing the housing.try spraying a lot of PB blaster or such into the bushing and see if it helps. Also slide spring down shaft and the small dust cover and spray in there also.To completely remove the brake pedal then the backing plate would ahve to be removed. It been a year since I ahve been in one, and I have trouble remembering stuff from yesterday!! :)
 
The brake shaft doesn't go through the differential housing. There is a freeze plug behind the bushing in side. My right one was packed with mud and grit. Distroyed ball end of shaft.
a52652.jpg

a52653.jpg
 
It pulls straight out, yours may be rusted in
there , pull the brake rod straight out and maybe
have to clean the socket and the hole. When
replacing it , put a little grease in there, on
the socket and the hole.


Stan

8N 146710
8N 179555
8N 197904
8N 199000
8N 254079
8N 362039
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top