jddrawbar

Well-known Member
Had to replace a hyd. hose on top of my loader, 1/2 in., 2 ft. long Gates, USA made. Decided to go ahead an replace both sides as they are almost 25 yrs. old. Stayed away from JD & had them made at NAPA. So, $108.00 later and a short fainting spell, I'm out the door. This was 2 little 2 ft. hoses!
 
I had a 6ft hose made with british fittings.
$88 out the door with tax included.

I don't really care that much about the price. It is what it is.
I'm happy I can get a special made hose made on a Saturday in minutes. Took me longer to drive 10 miles to town than it did to have hoses made..

Time is money. Glad to get the tractor going again to finish a job around the house..
 
It's always been WAY more expensive to have them made than to by them pre made at TSC, Farm and Home or even dealerships that still sell them off the shelf.
 
Next time if it is not an emergency that needs replaced right away contact the surplus center in Lincoln, NE. In the link if it holds the sort for 1/2 inch hose there will be 4 or 5 hoses, the scroll past the fittings and hose clamps. Then you will get into the hoses. A bit down the list they show the 2 ft or 24 inch hoses. Not a one of them is over $15. Now I am remembering you are in Canada, they may not ship there. Was this Canadian dollars?
Surplus Center
 
When I got my Dual loader several years ago I ordered replacement hoses for the ones from valve to where it hooks to pipe on loader frame. I also ordered replacements, a couple of each for ones that go to cylinders so I would have them on hand. All from Surplus center. Check fittings on the ends. Cheaper to get hoses without swivel on end and use separate swivel.
 
i have a jd dealer about 6 miles from me. they make up any hoses i need. i think they are reasonable on price.
 
Got 25 feet of 3/8 inch hose and four ends at my JD dealer this week. I haven't seen the bill yet. They sent me out of the door without any paper work. Do you suppose they didn't want to see me faint?
A week ago I had four 9.5Lx15 implement tires replaced. They also sent me home without a bill. But I have since received it. Tire, $138. Labor, per tire, $32.50. Disposal, per tire, $7. How much time on a tire machine to remove and replace a tire, 5 minutes?
 
I replaced two 32 inch 3/8 hoses with standard ends on my loader tractor this week. Tried TSC and Quality Farm first with no luck. Cost 95 bucks at the Hydraulic store to get them made up. I replaced the other two hoses just like them a couple years ago at the same store and thought then 60 bucks was bad.
 
I helped a neighbor pull a hose out of his crane the other day. It was 1/2 by 18 or 20 ft long rated at 6000 psi. He had a new one made at Parker. Cost was $700.
 

All the posts re 3/8" and 1/2" hoses got ripped off. You needed what you needed when you needed it and those suppliers took advantage. Find another source next time and send them a message.
 
something wrong there!! 4 fittings and 4 ft of hose. i can make that in 10 minutes. so i am not understanding that price. ok lets see... 10.00 each for fittings , ... 4 ft of hose say 40.00 tops equals 80.00 ... so maybe so , as i estimated high. so its possible. money for nothing... lol.
 
(quoted from post at 17:39:28 09/09/22) Got 25 feet of 3/8 inch hose and four ends at my JD dealer this week. I haven't seen the bill yet. They sent me out of the door without any paper work. Do you suppose they didn't want to see me faint?
A week ago I had four 9.5Lx15 implement tires replaced. They also sent me home without a bill. But I have since received it. Tire, $138. Labor, per tire, $32.50. Disposal, per tire, $7. How much time on a tire machine to remove and replace a tire, 5 minutes?

John Greedy dealers always charge $200 hours mecanics and clock them like if they were the slowest lazy man in the world equipped with only one pipe wrench and a screwdriver. He probably used the screwdriver on your tires.
You would have been much better off to go to a tire repair shop. Takes 10 minutes to do all 4 tires. You are not balancing them....
 
I had to replace one on my loader couple months ago. It was about 12 inches long with 1/2 pipe threads on one end and the other end had a 90 degree steel tube fitting. I was charged 30 bucks for the fitting and the total cost of the line was around 60 bucks
 
Yeah, there can be a big difference between " Gotta have it now!" prices and "it can wait I'll order online" prices.

Hose broke on my baler early this summer, decided to replace both. I too was shocked. But it was a "Gotta have it now" situation. And while shocked, was more than willing to pay it so I could get back to baling.

The rep from Parker happened to be there at the time...said at least I got them now, prices were going up 8% the following month..July
 
(quoted from post at 23:55:46 09/09/22) I just got back from Case dealer. Hyd. filter for my CX-100. $118 dollars. Whatcha gonna do?

FWIW, I keep a spreadsheet on my puter with every filter for every car, truck, tractor, lawnmower, and atv I own. With the Napa part number noted.
Then when Napa runs their 50% off sale in the spring, I'll stock up then. Works for me.
 
The 4 fittings were $69.96.....4 ft. of hose, $37.96 (central Tx. location) No apparent charge for labor, and yes it took less than 10 min.
 
I had a hose, about 2' long, blow out on my loader about 2 weeks ago. Went to a nearby (17mi one way) dealer. He made it up while I waited- it was shortly before their quitting time. @$47. This the second time this year I came in before closing- previously I needed a yoke for my baler PTO shaft. I called, he had it, I got it, I replaced it, and finished baling that evening. Can't beat that! Mark.
 
(quoted from post at 17:22:52 09/10/22) I had a hose, about 2' long, blow out on my loader about 2 weeks ago. Went to a nearby (17mi one way) dealer. He made it up while I waited- it was shortly before their quitting time. @$47. This the second time this year I came in before closing- previously I needed a yoke for my baler PTO shaft. I called, he had it, I got it, I replaced it, and finished baling that evening. Can't beat that! Mark.

Sounds like a good place to spend your money.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top