JD 3020 Wheel shift help

I need to move rears on a 3020 in to accommodate 30" row use. I have the manual and think I understand the steps. What I need to know is basically what am I in for? Should I spray bolts with liquid wrench in advance? Impact wrench ok?
Not my only vintage unit so I understand that when I adjust something, it is with the understanding that possibly this procedure hasn't been done since 1967.
Or am I too pessimistic and will see how this rim just glides across that axle as I turn pinion with one hand.
 
Loosen the three bolts on both sides of the wheel, tighten the two push bolts, use a 1/2 breaker bar so not to overdue it and break something, on both wheels and take it for a drive around the place. This is
if nothing moves right away and you might luck out. Just keep the tools handy and do chores, blade the driveway, etc. If the push bolts are able to come out, lube them with neversieze/grease and put them back
in. Just don't get in a hurry, can also get a length of pipe and a heavy plate to place over the axle and knock the wedges loose, can also cut half of the pipe off to just hit and the wedge with the pusher
bolts. Weld plate to pipe. Once the wedges are loose and if the pinion to move the wheel is stuck, you can remove the back wedge and slide wheel on axle to new spot, just make sure the grooves for the pinion
are clean.
 
Had a similar situation on my 730 standard. Couldn't get it to move using the book instructions. Soaked for many days with
PB blaster, etc. Ask my son, who is a Deere mechanic. He told me to take a large sledge hammer and wap the axle, NOT on the
end, but on the side. Being skeptical about marring the axle, I wrapped a piece of light tin around it. About the second or
third hit, it popped loose and I could move it using the pinon bolt. That was my experience. There have been many different
ways folks on here have gotten them loose and I'm sure there are lots of them that work. Just my experience.
 
First, how do the 2 pusher bolts look? Are they pitted and ate up? If they look bad screw them out completely. They have a soft metal keeper
on them and you will ruin that. Blow out the threads and lube them good and get a good used set of pusher bolts or brand new ones. Jack up the
tractor and remove the other 3 bolts. Screw in the pushers untill tight. We always hit the very end of the axle a few hits with a big sledge
hammer and then try to tighten each of the pushers. After the wedge comes loose do not be surprised if the pinion bolt will not turn. Spin the
center on the axle untill the pinion bolt is not touching the axle and then you can work on freeing it up. Did a 3020 last week that the
pinion was so rusty I just moved the center on the axle without even freeing it up. Often you get lucky and your pusher bolts do not need to
be replaced but it is no fun when you twist one off. Dad had a 4010 once that we ended up getting a jack hammer and removed the wedge in
pieces. I have a 3020 to do next week that is going to be a real challenge. Clean everything well before putting back together. Tom
 


When I was employed by JD dealer I was taught to squarely hit end of axle with a 10# sledge to aid in loosening wheels to axle.
Applying penetrating oil & driving tractor with loose wheel/axle attaching bolts also helps free wheels from axles
 
Advice on once you get them loose and tightening back up. Tighten the bolts up but don't over do it ! Just keep a wrench with you and check them often after you drive and work it. Good chance you will get more on them a few times and then you shouldn't get any more as they are settled in.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top