John Deere 4440

Reid1650

Member
What are yalls opinion. I will be looking to get one at the end of this season for starting my row crop operation up. I am also looking at a 12 row JD 7000 no till planter. How well with this tractor pull this? Also in a no till operation what tillage tools do I need? Right now I have a 14 ft disc but I dont think that no till demands a disc. Thanks Guys
 


I don't think a 4440 would handle a 12 row planter very well at all.

Out here (West Texas), you can find a 4840 for less money generally than a comparable 4440 - not sure why... But a 4840 would be much better suited to 12 row equipment...

Dad has a 4440, a 4850 & we have 2 4840's. We use a 12 row JD vacuum planter and usually use the 4850 on it.

Howard
 
Your 4440 would be about the same as my 1086, HP and weight wise.

I pull this Kinze set up for notill and have no problems.

My neighor pulls the same planter without the fert. coulters with a 4240.

The planter pulls as easy in notill as it does in tilled ground. The wheels seem to roll easier in notill cause they are not sinking intothe soil.

<a href="http://tinypic.com" target="_blank">
15d3lnd.jpg" border="0" alt="Image and video hosting by TinyPic
</a>
 
I pull my 12 row 7000 with my 806 . No turbo & pump set factory .
No problems except I can run to fast . I should plant under 6 MPH but I keep creeping up to 7 .
As late as its getting this year I'l sure I'll be over 7 IF I ever get in the field .
 
When I worked for a huge farmer that's the EXACT setup they used, a 4440 with a 12 row (30" spacing) planter. It seemed to be a good match, but 90 percent of the ground was flat as a pool table.
They also had a 4640 that did some tillage work but was often left unused because it had 20.8's on the rear while the 4440's had 18.4's. The bigger tires just didn't work well with the 30" rows. I believe the 4640's and 4840's don't bring as much just for that reason.
 
I m not an authority on no till, so won t even venture a guess on that. The 4440 is a solid tractor.

One thing to remember with the guys that are talking about the 46s and 48s is that they only have 1000 rpm pto. I don t think its so much the size of the rubber that affects the price, but the fact that your limited to bigger equip and tillage with the bigger ones. I m not big by any means, but I have equipment that is both 540 and 1000 and I can t afford to have a tractor that I m limited to use on only one piece of equipment..
 

That is a probem with the 06's. I had a 706 german deisel and it was hard to hold it down.

Even with 4 16's on the fast hitch.

steveormary
 
if you are going to no-til then there is no tillage involved therfore no tillage tools needed. 4440 is one of the best tractors ever made.Paul
 
My dad pulled a 7000 12 row set up with the Deere bubble coulters for no till with a 4020 for 2 years. Here in Michigan were I am it's pretty flat, and you didn't set any land speed records but it did it. After that it was on a 4430 for many many years. A 4440 is a better tractor than the 4430. Basically the same tractor without the pitfalls of the older 4030 series tractors. Guaranteed good trans, better quad range clutch pack, bigger engine (466 vs 404).

What limits 4840's up here is you are limited to 8 speed power shift only and the larger PTO.
 
I once had a neighbor that pulled a 12 row 7000 JD planter with a 4030 and no duals. A 4440 JD will easily pull a 12 row no-till planter.
 

I'm really surprised that so many folks think a 4440 would be a good fit for a 12 row planter.

In this area, a 4440 is generally used as a loader or utility tractor...

I guess I should mention, our 12 row vacuum is 3 point mounted, not drag type. It also has chemical boxes & trash whippers, which add to the weight.

Even with a full rack of weights on the 4840, with a full set of seed boxes on back, the front wheels just barely drag the ground while turning...

HH
 
Evening Howard, Hope all is well in the top end of the panhandle. Leave it to the ones with the smart mouth remarks to not understand how things are in our part of the world. We don't make fun of those who think a moldboard is still a primary tillage tool. 99 % of the moldboards in the upper panhandle have been shipped to Mexico, One farm auction at a time though there are still a few around in old fence rows or nonused equipment rows on some farms. I will bet LJ still has that old 3 bottom JD spinner, I know it hasn't been pulled since the 1968 at the latest. The last time it was pulled it was pulled with a 4010. A JD 4430/4440 is a high hp loader/chore tractor. A decent 6row tractor, fair at best on 8 row. Won't handle a 18ft heavy offet, Just not enough Power in the Blood. At least in High Plains SandyLoam or Blow Sand soils!
I am sure in other parts of the world a 4440 would be a nice tractor, pull a little plow, plant with a little planter, grow little corn LOL!
I am sorry Guys, I just couldn't resist. Yes they will do a ton of work just depends on the type of equipment it is put on on how well it will handle it. Grain cart work is a nice job for a 4430/4440.
Take care.
Later,
John A.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top