Looking for advice on attachments

oblivious

New User
Hey everyone.

I'm sorry that my first post here is a request but what can I do, I have no expertise to offer.

Anyway... I'm looking for some advice and you folks seem to know what you're talking about.

Situation is this. We are in Canada in the absolute middle of bum frack nowhere. We're 7 km (4.3 miles) up a windy, uphill, VERY rocky, VERY potholed, unmaintained logging road. It's dry and hard almost all year except for spring.

We have a John Deere 5425 up here, and we are looking at doing some road maintenance with it. Job description puts me in charge of it and I am totally clueless about tractors and how to use them. I was a suburban kid but now I'm living in the country. We also have a degelman 6-way blade and a bucket with a grapple.

The road needs:

- 4 miles of really bad potholes, ruts, and gulleys leveled, and
- crown re-established. Potentially also ditches established but I dunno if we'll go that far.

Apparently we used to hire a grader to do it periodically, but it costs about 2000 bucks to get one out here, which is almost the same cost as a new tractor implement.

So I've been doing a whole lot of research and come to some conclusions but they're suspect because I have no experience.

As far as I can tell we should get either a heavy duty box blade w/scarifiers or a rear blade, or both.
Used market sucks around here far as I can tell. New box blade from john deere is $2400 to $3200 CAD. Havent checked rear blade pricing yet but probably pretty similar.

So.. is it even feasible to do this? what is your recommendation?

looking forward to seeing what you think.
 
P.S. I tried working the road with the degelman 3500, it kind of works but it's pretty hard going and I'm concerned about the attachment points and it really just spreads the gravel around into the ditches with no way to crown or recover material.


Cheers
 
A box blade with (adjustable)teeth will loosen and smooth.But it will not be able to crown your drive. For that a common 3 point rear blade will be needed. The heavier the better.In other words,NOT a 'cheap' TSC type.I fought a long hard drive for years with a simple blade.It just bounced. Then I broke down and bought a box blade.Now,I got the drive cleaned up,I can now keep it that way. The first time,it too 3 hours for my 150 yard driveway.First gear,slow idle did the job. Now one or two passes in 3rd does the job.
 
Your going to need a HEAVY blade that you can angle and push from the side to the middle of
the road. It will also need down pressure from a hyd. cylinder on the top link. The good
news is.....you have a really good tractor!
 
To do the job as your wanting you pretty much need the machine made to do that as in a true Grader. At one time I kept mu mile long drive pretty good with a back blade but after I got this W Speed Patrol I will never go back to a back blade. If one keeps there eyes open and keeps looking a grader can be found for around what you pay to have it done
 
you need the machine for the job. not what ur thinking. roads where biult with old equipment back then plus good operators. you need an old grader or even an old crawler with tilting blade.and where in canada is this your talking about. plus you need access to some gravel.
 
A good heavy box blade with the scarifier teeth will work to help get ride of the pot holes. You say you already have a rear blade. So you can loosen up the road bed with the box blade teeth and then cut the crown with the rear blade. Angle it towards the center with the outer corner lowered just a little. This will bring the gravel back towards the middle. On the pot holes you need to set the teeth down on the box blade. Then make multiple passes loosening up the gravel down to the depth of the bottom of the pot hole. Then level your gravel. This is the only way to totally get ride of pot holes just filling them with loose gravel does not work. It just bounces out or is flushed out with traffic when they fill with water.

An eight foot heavy duty box blade would be about all you going to be able to pull loaded with gravel. When using the box blade they work better if you keep the box at least half full. This weight helps them work better. When looking at box blades try and find one that has replaceable scarifier teeth. The better one will have them. The teeth are held on with a roll pin so you can replace them easily. You will find that grading the drive works best a day or so after some rain. The rain will soften the road bed up enough that you can work the gravel better.

I have about a mile of drive ways to maintain it is easier with a box blade over a rear blade. You can grade the road bed without rolling the gravel off the edge of the drive. A rear blade has it place, such as pulling the rock back towards the middle, but to level a box blade works better. Also most box blades have two cutting edges facing back to back on the rear of the box. When you want to finish grade you can rock the box back with your top link. You can get it adjusted to where it rides the back cutting edge while the front just cuts a little bit. This "sweet" spot will take so adjustment to find but when you get it you can drop the box blade down and let it float independent of the tractor. You can then level easier/faster. When leveling with a rear mounted or even front mounted blade or bucket you can get long waves in the drive. Letting the box blade float when finishing your grade will help keep that to a minimum.


Now I will tell you a rear blade and box blade are a 1/2 inch at a time machine. Your not going to go out and cut the drive back to flat in a single pass. It takes time and skill to get good results but you can learn the skills pretty quickly. Time you have when compared to how long it takes to get equipment in.
 
I have moved a lot of dirt with box blade
to maintainer sized equipment and I agree
with everything jdseller said... you can
do alot with a box blade. Experience will
be your limiting factor for a while. And
don't expect to go out and make it perfect
all at once, it'll just keep getting better
and be something you maintain to your
standards.
 
You can put crown in your drive with a box
blade. Just run the right side a little bit
lower. Like is said below. Lengthen top
link till you find the sweet spot. Running
the box almost full. Set the teeth so they
dig a little when you shorten top link. We
have a hyd top link so is easy. Wait for a
rain then work your road. We just have a
King Cutter box blade. Less than half what
you said. Sure Rural King would truck ship
you one. Also Rome wasn't built in a day.
 

Some basic rules:Like JD seller said you have to cut to the bottom of the potholes, filling is good for just two rain events. You need a good crown: at least 6%, more if the other users will go with it. Without a good crown potholes will appear with just 6-8 vehicle passes. You need some workable but bindable material. I suggest 1.5 inch crushed gravel. Like JD seller said a box blade is 1/2 inch at a pass. Do you have that much time? for this sized job you may need to step up to a heavier wider blade and more power/weight to pull it. When you get into it if your blade is pulling up big boulders, you need to add material. The roadway needs to have adequate strength material under it. to stand up to trucks. The base material will not be stable if there is any amount of moisture in it. If you have water pooling on the high side the base will be unstable so you will need ditches and culverts.
 
All good advice, I have a 1/2 mile driveway that goes up hill and has 90*turn. The best advice don't try
to do the whole thing at once make a plan put on paper. split it up in sections, start with the worst
section first. Don't plan on doing work in the spring.
 

One of the old towed Adams road grader will be nice to repair your road. One is for sale in MN photo ads on YT. Ad # is 669911

mvphoto19370.jpg
 

All good advice. One thing I would like to add is water breaks. These are slight humps you put in the driveway to slow the speed of running water during a rain storm. If you do them right you will never have to do a major overhaul of the roadway due to erosion.


https://www.dirtandgravel.psu.edu/sites/default/files/General%20Resources/Technical%20Bulletins/TB_Grade_Breaks.pdf
[/url]
 
I don’t know where you live in Canada, it’s obviously not in he prairie region so my idea here is probably out of the question. When I was working in the Humboldt, sask area I saw a grader made from an old retired road grader with the front axle transmission and engine removed. It was made by a local company in that area but it’s been at least 10 years ago when I saw it so I’ve forgotten a few things about it. The blade functions were converted to hydraulic and if I remember right the front hitch hooked to the drawbar of the tractor pulling it. It might have had front dolly wheels, maybe not. Like I said it’s been awhile since I saw it. The owner did say this rig was built by a company, it wasn’t a one time farmer made outfit. Anyway, finding one of these rigs for sale in your area is probably out of the question but I thought I would throw it out there anyway.
 
That grader in the picture would never do that job. It is way to small and light weight. It is only good for maintaining a drive in good shape. And a 3 point blade you cannot get a level job with as when a front wheel drops in a hole it will raise the blade up and as soon as the front wheel gets out of the hole the blade will drop down to want to dig a hole and every pass make it worse. I only have the 3pt blade.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top