MF 200B dozer parts needed

[seeburgrepair]

I need the pickup tube..off the screen head pickup of the sump off the Hydraulic reverser tranny
I only need the first about 14 inches.. there is a factory coupling at about 14 inches...
I only need that first section...
someone somehow has flatened it in 2 spots. and the pump cannot keep up with demand when oil is hot...
I also have a leak between the Clutch inch/pause housing and oil distrubutor plate.. looks like just two studs at top and bottom to take off. i can make a gasket. but would someone have NEW gaskets ?? any MF dealers anywhere left with SMALL NOS PARTS like gaskets ?
dozer runs when cold..drive clutches ingage. but when a little warmed up .. wont move as oil leak drops level and SMASHED PICKUP TUBE wont keep up with demand.. i think just fixing the picktube will solve the problem because when i add enough oil to reverser tranny the dozer takes off ok...
when level is fairly low. the only way i got it to move was....pull back all the way on both levers and hold momentarily and SLOWLY allow them to move forward till CLUTCHES engage....then they lockup solid and moves lots of dirt.. till i put in reverse.. then wont move aagin.... till levers reset and or ADD ENOUGH OIL TO reverser tranny...
My first dozer and the guy that sold it ...claimed WORKS PERFECT.. yeh right... NO LEAKS.. he said.. dirty bird.. but im sure the leaks being fixed and tube replaced will solve the problem... i will check the suction side screen also.. looks like fun to take out...
I REEEEEEEEEEEEEELY LIKE THIS MF 200B..has lots of power....and 6 way blade...
Mike in Cambridge Ohio 740 638 5059
I would like to buy another 200B for parts.. no engine is ok....
any help appreciated...
thanks, Mike

 

[agpilot]

Hello seeburgrepair: Did you see/read the post down below this Crawler topic on the Massey MF tractor forum?? It was posted about May 10 and was titled MF 200 Extra parts.. Sounds like maybe you could possibly find a repair shop to make the part you need. Doesn't need to be a shop for MF crawlers.. just need to find a real handy do-it-yourself type person? Anyway, good luck getting it fixed. I had a 1970 200 25-30 years ago and really liked it. I put over 1000 hours on it.. ag

 

[seeburgrepair]

HI, thanks for the info.. some 200 parts wont fit as 200B is different.. from pics i see the 200 is not like the 200B on the hydraulic reverser...i see a 200 center section on ebay and it doesnt have a hydrualic reverser..? odd..
i can make the tube but just be easier if i had an original to put on....
tightened the nuts on the clutch incher housing and most of the leak stopped...has TRANNY fluied in it and that toooo thin....
this is a REALLY NICE RUNNING DOZER....LOTS OF POWER.. im glad i bought it...looks like most dozers are FUN to fix tho... tight quarters...
Mike...

 

[Steve in South Jersey]

Are you talking about the aproximatly 3/4 inch steel tube, a couple feet long?

 

[seeburgrepair]

HI, the tube i need attaches to the cap of the screen cover..the tube supplys the fluid for the pump for the reverser tranny

The tube attaches to the cover and about 14 inches up from the cap is a factory connection

so it can be taken apart... i only need the 14 inch section...
Do you have a 200B for parts ?

I will try and post a picture as soon as i figure out how...

thanks, Mike

 

[seeburgrepair]

MF200B PROBLEM...WHEN WARMED UP QUITS MOVING..

ANSWER.. WAS....

HIGH PRESSURE RELEIF VALVE NEEDED SHIMMED UP...

DOZER WORKS PERFECT NOW....

GUY THAT SOLD IT TO ME DIDNT KNOW CRAP AND THOUGHT HE WOULD DUMP THE DOZER...

IM SURE HE THOUGHT HE NEEDED HIGH DOLLOR REPAIRS..

IM A MASTER MECHANIC .. AND WITH A LITTLE THINKING FIGURED OUT THE FIX..

THIS THING RUNS LIKE A MILLION BUCKS...

WHEEEEEEEEEEEEEEEEEEEEEEEEEEEE..!!!!!!!!

 

[seeburgrepair]

I also built a 3/4 inch pickup tube...that was a real lot of fun.. but actually there was JUST ENOUGH ROOM TO USE AN OPEN END WRENCH ON EACH END..

WHAT LUCK..!!

HARD TO BELIEVE THE POWER THIS LITTLE PERKINS PUTS OUT...