need some advice

had my 8N for two months starts up first crank 95% of the time. however the wiring scares me. a home made conversion to 12 volt. 12g romex used for part a generator looking like from a locomotive with a mounting bracket pointing off in space two voltage regulators.... Would you do a alternator conversion? 12 volt or 6? or go back to 6 volt generator. I am no electrical engineer so I need it to be easy and by the book to troubleshoot. Thanks for help.
 
Most problems we read about w/ 12v conversions are as a result of folks getting in over their heads or buying tractors w/ "Bubba" conversions, and now the new owner is stuck with trying to figure it out. You have a "Bubba" conversion & are wise to just trash it & start over.

One key consideration is the coil: is it on the front or side of the engine?

Another is originality; it was 6v from the factory.

Lastly, it's cost. You have a battery, so you need a bracket, wires & an alternator. Getting to 6v means a generator, probably a bracket, a battery, wires, battery cables & a v/r. Compare the costs.

The advantage of an OEM 6v is that everyone (just about) understands how they work.....just like they did in 1939. Parts are readily available.

A 12v conversion w/ a Delco 10SI alternator is fairly common; it gets more difficult other alternators and w/ a frontmount distributor due to resistor requirements, but by no means is it a show-stopper. Just understand that a frontmount conversion is going to require that you understand & apply Ohm's Law, or you are going to be back here asking why your coil burnt up.

Bottom line.....means you have a 12v battery, I'd say it's cheaper to get a good quality kit & make it 12v. Lots of folks here can help.

But, if you want it to be like Henry made it, go back to 6v at probably a higher cost.
50 Tips
 
Well, I don't have livestock or a real farm here, so if my 2 started on 1st crank 95% of the time, I'd leave them alone until they didn't - unless you want a trailer queen - which I don't. I always believed in; "If it hain't broke, don't try to fix it."
 
The romex is most likely solid wire (yes I have seen stranded romex before). I would at least get rid of that. David....
 
(quoted from post at 15:36:27 06/25/08) had my 8N for two months starts up first crank 95% of the time. however the wiring scares me. a home made conversion to 12 volt. 12g romex used for part a generator looking like from a locomotive with a mounting bracket pointing off in space two voltage regulators.... Would you do a alternator conversion? 12 volt or 6? or go back to 6 volt generator. I am no electrical engineer so I need it to be easy and by the book to troubleshoot. Thanks for help.

I posted a topic in the last 2 or 3 days, where one can have 6v positive ground, one wire, Chevy alternators.

I'd have to find it in the AM though...

That's what I have been running for 25 years.
 
I'd gut it and go 12 volt alternator unless you have a reason to go back to 6 volt. You can buy new harnesses for 12 volt conversions, or just make your own as you go, 1 wire at a time. I've re-wired many and don't understand why so many make them out to be difficult. They have basically no more wires than a 6v setup. Only 1 or 2 from the alternator (go 2 wire). Use a Delco as stated by others. The one main thing you need to understand is the coil/resistor setup. Before you begin pull the hood. Its not that hard and its much easier wiring. Take photos before you begin especially the dash. Chase the wire to the coil and observe if there are resistors in there now. If you don't have a 12 volt coil, buy one if you are able and skip the extra resistor. With a 12 volt coil you only need the factory resistor on the dash. One more way to reduce complications. Use the 2nd wire to the alternator to excite it. Someone here has a photo with a pair of diodes to prevent feedback. You can also to an extra light in the circuit to draw down the alternator. My 48 is wired like that. Do the diodes.
This will likely ignite the voltage debate 6 vs 12 but its your tractor.
 
"With a 12 volt coil you only need the factory resistor on the dash."

Unfortunately, that is no longer the case.


The only difference between a "6v" coil & a "12v" coil is the internal resistance.

It used to be before the "Land of Almost Right" started making coils that you could count on a 12v frontmount coil as having 3 ohms of internal resistance & the 6v coils as having 1.5 ohms or less. Thus, thanks to Ohm's Law, you could calculate what additional resistance you needed in the circuit to limit coil current to 3.5 amps. So, you will need to measure the internal resistance of that alleged 12v coil & see what it is.

Sometime back, a few regulars on this board measured the internal resistance of some new "12v" coils & found the resistance to be all over the scale.
50 Tips
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top