First penetrating oil I was introduced to was K&W Knock'er Loose. 1967 or 68. The can was copper colored and black.Wasn't that a K&W product at one time? Seems to me it was pretty good but I haven't seen it around for a long time.
It is still rated the best overall penetrant.First penetrating oil I was introduced to was K&W Knock'er Loose. 1967 or 68. The can was copper colored and black.
My father's advice also . Often less corrosion in that direction allowing you to break the initial bond .My uncle told me if you got a nut that won't loosen to tighten it up first.
He was dead serious, the man is in his 80's so I have to believe him.
When my son started to work at Cat Engine plant they still Re-manufactured engines. He took them apart, they bought Kroil oil by the Barrell and Sprayed all those used Engines down before taking them apart.I like Kroil. Now it's on the shelf at Rural King...
Well, I've got about 30 years on you, as far as ASE tech experience goes, and I haven't seen much difference from one to the next. Loose Juice, Knock 'Er Loose, Kroil, Liquid Wrench, Deep Creep, homemade diesel/Marvel Mystery Oil or Acetone/ATF, Freeze Off and everyone's favorite fad penetrating oil PB Blaster ...even Nissan had a pretty decent one, they all have about the same ingredients and they all work about the same. None of them magically make a rusted bolt come loose. The one machinist magazine study said acetone/atf worked better than anything commercial and behind that was Kroil, then Liquid Wrench with the rest of the brands trailing, but they only tested about 6 or 7 products so who knows? And is that a thing? In the south they use propane instead of acetylene? I worked in one shop where we used oxy/propane, but that was because we were also a propane dealer.I was a professional ASE tech for about 8 years until the financial collapse of 08. I tried many different brands over the years and found Mopar Rust penetrant to be the best, but I’m not paying that kind of money for a marginally better product. I found that most any commercial rust penetrant left to soak for a few minutes, followed by a mapp gas or propane torch was the superior method by a very wide margin. Most dealers at least in the south don’t have oxyacetylene torches. Sorry if that was a sidetrack to the question, but I’ve probably tried at least 20 depending on what was in a parts department or at a parts store.
We generally didn’t have rust issues like the vehicles I’ve see that have been around salt water or where the roads are de-iced, so there wasn’t much need for a two tank torch. Most of the guys kept a torch with a bottle like you use for plumbing or even butane torches handy for when we got a the odd duck rust monster in to work on. A few shops had the two tank torches, but it was the exception and usually for a body shop if there was one at that dealer. The plumbers torch with PB Blaster or Kroil is what I use now at my place because it’s what I keep on hand. Nothing on my late year 57 641 or my 65 Mustang that I’ve had for 32 years has defeated the propane thus far, but it is inland Georgia.Well, I've got about 30 years on you, as far as ASE tech experience goes, and I haven't seen much difference from one to the next. Loose Juice, Knock 'Er Loose, Kroil, Liquid Wrench, Deep Creep, homemade diesel/Marvel Mystery Oil or Acetone/ATF, Freeze Off and everyone's favorite fad penetrating oil PB Blaster ...even Nissan had a pretty decent one, they all have about the same ingredients and they all work about the same. None of them magically make a rusted bolt come loose. The one machinist magazine study said acetone/atf worked better than anything commercial and behind that was Kroil, then Liquid Wrench with the rest of the brands trailing, but they only tested about 6 or 7 products so who knows? And is that a thing? In the south they use propane instead of acetylene? I worked in one shop where we used oxy/propane, but that was because we were also a propane dealer.
Induction heaters work great. I prefer them over a torch for a lot of things.Torches are not the only way to heat a fastener or joint, and sometimes just simply cannot be used due to proximity or environment. Induction heaters can be a real asset in tight quarters, around wiring or fuel lines, or in areas where there is combustible dust or flammable gas or vapor.
It's parallel to a pipeline freezer used by plumbers to isolate a line for a valve replacement or hot tap, and while only having been around for about 50 years, we wonder how we ever managed without it. Induction heating has been around since before the depression, but it is now a lot more portable.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy