OT/ Brake Bleeders

JOB

Member
Does anyone have a good souution for getting bleeder valves out of calipers or wheel cylinders. I currently have the calipers off the truck and have put penetrating oil around the plugs they have been soaking for 4 days now and they are still stuburn. Heat I feel will wreck the rubber inside the caliper.Will a little heat work? Any suggestions? Thanks
 
heat and then try using tap sockets or a 6 point socket and breaker bar that you can hit. You pull on the handle while pounding down on the socket with a hammer. works like an impact .
 
When your done get some of them rubber caps that keep dirt and water out of the bleeders they are worth thier weight in gold.
 
I will give a little heat a try. One of the hex heads is no longer hex so a 6 point won't work on that one. They have not been turned in many years.
 
If, after all the heating and banging and twisting is done, and if the bleeder breaks off. NAPA has a nice repair kit. Just drill, tap, install bushing and new bleeder and you are done.

Jack
 
Take a BFH and hit them a few times. If they are going to come loose they will by doing that. If that does not work try again but if it does not work after 2 or 3 tries it will never brake free. BTDT many many times
Hobby farm
 
Heat them red hot and douse with water..done that thousands of times on siezed bleeder screws,then put a small socket on that fits tight and they will turn out easily.
 
If you have the female TORX sockets (which are used quite a bit this side of the pond), they are great for hammering over a chewed up head. I've had much more luck with the male TORX bits used as Eazy-outs too on snapped studs. Failing that hammer a twelve point socket over the nipples & use heat
 
I have has some luck with quickly heating the bleed valve dull red hot with a small tip and allowing it to cool. May have to repeat if still stuck.
Concentrating the heat in the bleed valve seems to transfer enough heat to the threaded part to loosen rust while not heating the cylinder/caliper enough to damage internal rubber parts.
 
One other thing to consider, how perfect are the calipers /cylinders ? Are they worth spending a lot of time on a repair ?

I learned to check that after an experience with a full size 79 Dodge van. The front calipers were sticking and causing brake drag / heating. After removing and inspecting I found the pistons a bit scored and caliper body a bit rust pitted. I honed the caliper bodys and installed a new $10 piston /seal kit.
After 6 months they were sticking again.
I rehoned and installed another $10 repair kit.
6 months later they were sticking again. You could see by the position of the scoring that the caliper body was warping and pinching down on the pistons.
I said to myself, "Now I got to spend the big bucks and buy rebuilt calipers". Stopped at the local NAPA and asked for rebuilt calipers, ready for the bad news on price. Counter guy said "sure we got them in stock, $13 each"
Thought, Oh my gosh, I spent all that time and $20 worth of kits on the old ones and still had nothing. The rebuilt $13 calipers were a different casting number and have been trouble free for 15 years. Costly lesson. :-(
 
Best thing I have found is to soak them with Fluid Film and then I use a Makita cordless impact drill with a 6 point socket. I try to back them out first, if that doesn't work, I try to tighten them and then switch back and forth.
 
Heat the fitting with an acetylene torch until it turns red, then immediately grab it with a Vise Grip. It'll come right out. Since they're small, it takes very little heat to do the trick.
 
Why would you even mess with it? They are so cheap to buy and you can get them what they call "fully loaded" which is with new hardware like anchor bolts and bushings.Mark
 
Reman calipers and cylinders are the best solution. If you're bound and determined to get them loose, I find that if I use my air hammer with a pointed punch in it and hammer around the screw, 8 in 10 will come out easily.
 
If you do get them out, or buy new ones. try wrapping teflon thread tape around the threads when reinstalling the bleader. It will keep rust form forming around the threads. Plus I usually smeare grease around the bleeder screw. I have had them bust off, and it's not fun. I put the calipers in a mill to drill out the bleeder screw. Stan
 
If you apply any heat to a hydraulic brake component make sure there is an opening for the brake fluid to escape. It will build pressure and burst a rubber line somewhere and it's very flammable.
 
If you apply any heat to the caliper make sure the system is open somewhere for the brake fluid to escape. It will build pressure and burst a rubber line some where.

Brake fluid does not need a spark to ignite it, just heat and if the system is under any pressure you will have a flame thrower. Been there believe me it's not fun and some one can get seriously burnt.

Just replace the calipers with "Fully Loaded" ones that come with new pads and the whole 9 yards. The time you'll save you'll be money ahead.
 
I forgot to mention on my post below. Don't skimp on any brake system component.

The brakes are the most important system on any vehicle.

If you can start a vehicle you have to make sure you can stop it!
 
This is a truck that I use around the house to haul wood with, it has not been liscened in maybe five years. I do not want to buy calipers unless I have to. I just replaced all the steel lines from the Master cylinder to the rubber lines. I had to cut the rubber lines. I don't think I put 10 miles a year on it. Thanks for your suggestions
 
John, that's a good point. He did say he had the calipers off the vehicle. I did do this on the vehicle once without loosening the brake line. Hot fluid shot out and gave me a mild burn on the wrist.
 
Here's the bigger question- Why is brake fluid hydroscopic? It holds water and attracts rust. Why not use an anti-corrosion oil product? Makes no sense to me. Hydraulics are hydraulics. You might as well use salt water as brake fluid.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top