Pertronix.....

I'm having issues with the points burning out fairly quickly on my tractor and I am contemplating on installing pertronix system. I have bought my points from many places with the same results. Does the tractor have to be a 12 volt system to work or can you stick with the stock 6 volt?
 

You would be better off to double shoot the pitting problem first. Most likely you have a coil/ballast resistor problem.
 
You -can- get a six volt version - I had one on my 51 8N. I did NOT like it and had more trouble with it than I ever did with points. The problem was that voltage while using the starter would drop below the threshold to trigger the Pertronix module in the distributor when the magnet went by. Just hooking up the battery charger was enough voltage boost to start the tractor immediately. I went back to points - I sold the 8N soon after and only have one gas tractor left - an 871. It came 12 volts and has points - everything works as it should - I have no reason to change. That was at least 5 years ago, and maybe they have improved over the years, but I would not gamble on it. If it were mine and I wanted to go breakerless, I would go to 12 volt at the same time.
 
Tell us exactly what the " burned up " points look like. Metal transfer? Discolored? What gap did you initially set them at and what was the gap when you noticed they were burned? Have you checked for bushing wear?
75 Tips
 

Would you like to explain how you tested the module and determined it did not trigger. I am not doubting you for a 6V EI system to operate satisfactory all you ducks have to be in a row.

I think the main concern is the module does not pull the coil to a true ground. Like a conventional system all your ducks need to be in a row to get the maximum performance from the ignition coil. Any little glitch in the system and the coil is not going to perform well. A 6V EI already has one little glitch built into it, it does not pull the coil to a true ground. This does not seam to affect a 12V system like a 6V system if you had a weak coil the outcome would be the same. A weak coil could work on a conventional system because because its pulled to a true ground.

I am not selling a EI system but do doubt all the post that claim it wont work well because it does work on a 6V system.
 
(quoted from post at 05:56:09 05/30/18) Tell us exactly what the " burned up " points look like. Metal transfer? Discolored? What gap did you initially set them at and what was the gap when you noticed they were burned? Have you checked for bushing wear?
75 Tips

Bruce, Usually they look just severely discolored. I set them at the factory .015. It will run great for the time being then performance will start to decline and it will be harder to start.
 
Bruce, could just be the points. My last 8N that had points would go through a set of points in about 6 hours. I rebuilt the distributer, used the cam lube supplied with the points. Replaced the condenser. New coil and wiring harness and ballast resistor too. This was with Standard ignition products. Check the gap a failure and it was spot on. Then with the last set I noticed something I had missed. Only about 1/2 of the contact surface was making contact. I had enough of the trying to find decent parts nonsense and went EI. Haven't had any problems yet, 2 years and a lot of hours.

For the OP: I was informed when I researched EI that I would be better off going with 12 volt. As far as I'm concerned one of the best mods you can do to these old tractors if you are using them daily. And that's with or without an amp meter or volt meter.

Rick
 
EI or no EI? Too many posts have been written on this subject. There are good arguments on both sides.

Lets bottom line it.

As Hobo points out, you still have a semiconductor junction in the circuit, not a straight to ground reference like breakers give you.

EI works. I'm a fan of it on my 2014 ford E350, I'm less of a fan of it on a 55 ford tractor.

6v and EI is 1 step above points, if you are frontmount, get the coil conversion setup, and gain a little breathing room. As has been noted, 6v EI are sensitive to low voltage. Its EASY to hit the marginal/fail threshold on 6v EI voltage, between wire harness age, condition, type of connections and connectors, battery health, charge system health, starter health. You can hit failure threshold on trigger voltages pretty easy on a marginal system. 12v suffers the same problems, but has much more breathing room.

I tell most people that if they lack the skills to maintain a breaker system, then EI may not be a perfect fix because the electrical system needs maintenance, and its the same skill set.

Lastly. .. If you are going thru breakers in days or hours, YOU HAVE PROBLEMS other than the points set.
Either you are gapping wrong, mechanically the gap can't be maintained or is erratic, you are not cleaning the breakers, or you are sanding them and leaving grit that further exacerbates the problem. ( a fine tooth hone is better but not great, its a bandaid/diagnostic tool ). You may be getting oil or combustion products in the breaker area, you may have an ill fitting cap or other openings letting too much outside environment in.

Folks, I live in Florida, it has rained about the last 16 days. The 2 tractors I use the most are a mutt 950 & an 850. They sit outside 24/7.
I have not bought a set of breaker contacts in YEARS!
These tractors get corrective maintenance only, these are my beater workers. Bunji holding batteries in. Gator clio hotwire on the 950 in place of a key. The 850 just got a brake line I bent up to replace a leaky power steering line, and a 1g thinner can with a hose barb is the gas tank because the loader frame won't let me take the hood off. Once a year oil change and breather service, and top off other sumps, air tires. Adjust carb in winter, check breakers when needed, and it hasn't been in years, though I did dab some ml1 on the lobes on each this year.

Those tractors will crank up in 2-3 revs. 1 if already warmed that day.

If your tractor won't start and are eating points fast... You have a problem! And its not who made the points!
 
(quoted from post at 06:30:09 05/30/18) Bruce, could just be the points. My last 8N that had points would go through a set of points in about 6 hours. I rebuilt the distributer, used the cam lube supplied with the points. Replaced the condenser. New coil and wiring harness and ballast resistor too. This was with Standard ignition products. Check the gap a failure and it was spot on. Then with the last set I noticed something I had missed. Only about 1/2 of the contact surface was making contact. I had enough of the trying to find decent parts nonsense and went EI. Haven't had any problems yet, 2 years and a lot of hours.

For the OP: I was informed when I researched EI that I would be better off going with 12 volt. As far as I'm concerned one of the best mods you can do to these old tractors if you are using them daily. And that's with or without an amp meter or volt meter.

Rick

With the end of family farms in my town I'd found myself without a decent source for my 8n parts. I started buying my tune-up parts online, from Stiener Tractor. I got a whole 10 hours, collectively, of mowing with my Woods 5ft finished mower till the tractor began running bad, died and would not restart.

Upon removing the points I saw that the contacts on the points were mostly gone! Burned away.

I orded another set and had pretty much the same result.

I then went into a good NAPA store and asked for a quality brand of ignition points. He sold me a set of Echlin. Those points have been my tractor for 3 years now!

Never buy cheap parts for a job you want done well. That's the lesson I learned here.
 
Were they Echlin? NAPA will sell discount parts as well as premium. The counter guy I talked to about this when I bought my Echlin points there, said that boat owners won't install any other brand since the discount brands (Chinese manufactured) became so prevelant.
 
(quoted from post at 10:09:36 05/30/18) EI or no EI? Too many posts have been written on this subject. There are good arguments on both sides.

Lets bottom line it.

As Hobo points out, you still have a semiconductor junction in the circuit, not a straight to ground reference like breakers give you.

EI works. I'm a fan of it on my 2014 ford E350, I'm less of a fan of it on a 55 ford tractor.

6v and EI is 1 step above points, if you are frontmount, get the coil conversion setup, and gain a little breathing room. As has been noted, 6v EI are sensitive to low voltage. Its EASY to hit the marginal/fail threshold on 6v EI voltage, between wire harness age, condition, type of connections and connectors, battery health, charge system health, starter health. You can hit failure threshold on trigger voltages pretty easy on a marginal system. 12v suffers the same problems, but has much more breathing room.

I tell most people that if they lack the skills to maintain a breaker system, then EI may not be a perfect fix because the electrical system needs maintenance, and its the same skill set.

Lastly. .. If you are going thru breakers in days or hours, YOU HAVE PROBLEMS other than the points set.
Either you are gapping wrong, mechanically the gap can't be maintained or is erratic, you are not cleaning the breakers, or you are sanding them and leaving grit that further exacerbates the problem. ( a fine tooth hone is better but not great, its a bandaid/diagnostic tool ). You may be getting oil or combustion products in the breaker area, you may have an ill fitting cap or other openings letting too much outside environment in.

Folks, I live in Florida, it has rained about the last 16 days. The 2 tractors I use the most are a mutt 950 & an 850. They sit outside 24/7.
I have not bought a set of breaker contacts in YEARS!
These tractors get corrective maintenance only, these are my beater workers. Bunji holding batteries in. Gator clio hotwire on the 950 in place of a key. The 850 just got a brake line I bent up to replace a leaky power steering line, and a 1g thinner can with a hose barb is the gas tank because the loader frame won't let me take the hood off. Once a year oil change and breather service, and top off other sumps, air tires. Adjust carb in winter, check breakers when needed, and it hasn't been in years, though I did dab some ml1 on the lobes on each this year.

Those tractors will crank up in 2-3 revs. 1 if already warmed that day.

If your tractor won't start and are eating points fast... You have a problem! And its not who made the points!
hat last sentence carries a lot of weight, for sure! When coil current is correct and distributor not worn out, points will last me 10 to 15 years in 8Ns, Farmall, 1962 PU, IH combine, etc. Most run weekly , but will have some "long sitters" such as combine where I may need to clean a bit of corrosion to get sparking. Combine hasn't had new points since 1986.
 
15-20 hours? then your coil current is too high, or the points are dirty or not gapped correctly, or the condensor is bad, or
they are not striking square due to a distribuitor cam or breaker plate issue.
 
(quoted from post at 11:04:13 05/30/18) 15-20 hours? then your coil current is too high, or the points are dirty or not gapped correctly, or the condensor is bad, or
they are not striking square due to a distribuitor cam or breaker plate issue.

I know the gap is .015. When I replace the points I always replace the condenser too because I hate tearing the dang thing apart. lol. I replaced the coil recently as well.
 
When you buy points, do you buy a condenser too? It used to be that we always changed points and condenser at the same time. It sounds like your condenser isn't doing it's job. Take a couple of minutes and read Bruce (VA)'s explanation of the Kettering ignition system in Basic Question by RobertIL just below your post.
 
(quoted from post at 11:44:22 05/30/18) When you buy points, do you buy a condenser too? It used to be that we always changed points and condenser at the same time. It sounds like your condenser isn't doing it's job. Take a couple of minutes and read Bruce (VA)'s explanation of the Kettering ignition system in Basic Question by RobertIL just below your post.

Yes I replace both. Will do on the read.
 
(quoted from post at 15:26:03 05/30/18)
(quoted from post at 11:44:22 05/30/18) When you buy points, do you buy a condenser too? It used to be that we always changed points and condenser at the same time. It sounds like your condenser isn't doing it's job. Take a couple of minutes and read Bruce (VA)'s explanation of the Kettering ignition system in Basic Question by RobertIL just below your post.

Yes I replace both. Will do on the read.
Does the ballast resistor get hot?
 
(quoted from post at 12:27:42 05/30/18)
(quoted from post at 15:26:03 05/30/18)
(quoted from post at 11:44:22 05/30/18) When you buy points, do you buy a condenser too? It used to be that we always changed points and condenser at the same time. It sounds like your condenser isn't doing it's job. Take a couple of minutes and read Bruce (VA)'s explanation of the Kettering ignition system in Basic Question by RobertIL just below your post.

Yes I replace both. Will do on the read.
Does the ballast resistor get hot?

Hot to touch?
 
(quoted from post at 06:40:57 05/31/18)
(quoted from post at 12:27:42 05/30/18)
(quoted from post at 15:26:03 05/30/18)
(quoted from post at 11:44:22 05/30/18) When you buy points, do you buy a condenser too? It used to be that we always changed points and condenser at the same time. It sounds like your condenser isn't doing it's job. Take a couple of minutes and read Bruce (VA)'s explanation of the Kettering ignition system in Basic Question by RobertIL just below your post.

Yes I replace both. Will do on the read.
Does the ballast resistor get hot?

Hot to touch?
owever you may be able to characterize its temperature.......too hot to hold finger on, burnt me, about like freshly brewed coffee, about as warm as my hand, about as warm as my wife, ?????
 
Front or angle mount distributor? STEINER sells the standard cheap plastic rubbing block points -poor life span. The ECHLIN or BLUE STREAK/STANDRAD IGNTION points, sold at NAPA or SUMMIT AUTOMOTIVE with the phenolic rubbing block are the best. Caution exercised as even these brands are now exhibiting limited adjustment and many cannot get the .015" gap set on the front mount.

Tim Daley(MI)
 

tim, your reply is not visible in modern view (which the OP uses) because u mentioned s t e i n e r.
 
I changed out my front mount 8N 6V to a 12v and installed EI. I could not be more satisfied. Tractor runs great every time and all day. Sits sometimes a couple of weeks between starts and fires up right away with no choke. Nice easy idle with no miss. Also it sits in the outside in the weather.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top