Question about Massey Ferguson #12

Hello all,

My father just purchased a Massey Ferguson #12 (painted on the front) baler from an auction.

She's been working OK.... Every fifth or six bale it seems like it knots, but the "passenger side" or right side knot or inside knot if viewing the baler from the back will tie, but then as the bales are pushed out the chute and the slack in the cicel twine is absorbed by the hay expanding, the knot will pull out.


Once it pulls out, we are left with a single straight strand of cicel going down through the hay where the pins came up through, and the knotted (overhand knot) is left on the top of the bale.


Sometimes the knot will come out before it even clears the knotting mechanism, and when that happens there are two strands of cicel coming out of the mechanism. That loose end of twine gets cut the next time the knotter and cutter functions, and that is when I pull it out of there to prevent tangles.



First things first, is it normal for the freshly tied bales (still in the chute) to have all kinds of slack in the twine? Once the bale comes further out the chute and then finally is on the ramp before it hits the ground, that slack is no longer there.


It appears to me as though the cutter may be cutting the cicel too close to the knot, and when that knot is drawn tight by the hay expanding it is simply pulling that cut end out. How can we adjust the cutter away from the knot?


If anybody is familiar with this problem, please let me know. We have been scouring our John Deere baler book as everything seems similar (knotting problems etc) but we haven't been able to pinpoint this one.

We already tried adjusting the pressure plate on the twine box but that hasn't helped.

I keep telling dad that he just bought a really fancy piece of scrap metal, he's laughed but then says that we'll figure the problem out eventually. Problem is, we don't bale but a few hundred bales a year and it could take centuries to figure this problem out.

Ya'll seem like a knowledgeable group...
 
One other thing,

Not sure if this will help or not, But I've noticed that as the machine is packing hay in, it appears as though the cord on the right (inside) (problem side) Doesn't have the same tension that the left (outside) one does. It's to the point in fact where the twine is not even in that twine "disc" or the stack of discs with the grove in it. I can put it in there but as the machine packs the hay in the cord works its way out, while the other side stays put.
 

I am going to check the twine tension now. I seem to remember as we tightened the pressure plate seeing two springs mounted inside the shield that is to the left of the twine box. The twine ran through a loop in the springs. I remember one spring being bent differently than the other, perhaps this difference is causing too much slack in the twine from not applying enough tension.
 

I've got the repair manual in pdf. Send me an email address and I'll forward it to you.

Some things to look at. Roll it over by hand, trip the knotter and cycle it through slowly. Watch that the needles are extending high enough for the twine disc to grab the string really good and that the needles are lightly rubbing the knotter frame when fully extended. also check the needles to see if there are grooves worn in the eyes. If there are grooves take them out and weld and polish them back to a round shape. Also check the ceramic guides that the twine runs through. They get worn also, you can just loosen the clamps and rotate them. The tucker fingers are also adjustable. Make sure they are grabbing the string good. The tension on the bill hooks is also adjustable. I wouldn't mess with timing on the twine disc till all these other things are looked at. The tucker fingers should pull the twine back as far as possible but give the needles enough room to clear.

The service manual covers all these adjustments.
 
(quoted from post at 05:03:53 07/14/09)
I've got the repair manual in pdf. Send me an email address and I'll forward it to you.

Some things to look at. Roll it over by hand, trip the knotter and cycle it through slowly. Watch that the needles are extending high enough for the twine disc to grab the string really good and that the needles are lightly rubbing the knotter frame when fully extended. also check the needles to see if there are grooves worn in the eyes. If there are grooves take them out and weld and polish them back to a round shape. Also check the ceramic guides that the twine runs through. They get worn also, you can just loosen the clamps and rotate them. The tucker fingers are also adjustable. Make sure they are grabbing the string good. The tension on the bill hooks is also adjustable. I wouldn't mess with timing on the twine disc till all these other things are looked at. The tucker fingers should pull the twine back as far as possible but give the needles enough room to clear.

The service manual covers all these adjustments.


Much Appreciated!

Email at [email protected]


Thank you. Anybody else with any ideas please post them!


I will go check what you've mentioned now.
 
Most times it's just wear issues. Look at the things I suggested. The bill hooks have roller cams that wear. There are also roller cams that drive the tucker fingers. These parts get worn as well as the needles and they need the slop adjusted out of them or replaced, your choice.

Odds are very good you can adjust and repair any issues and be up and running soon.

Sounds like it's mostly working, just needs a little tweaking.

Edit, I forgot to mention. There are diagrams of the knotter assembly at agcopartsbooks.com The pictures from the scan of the manual leave a lot to be desired but, you can see all the adjustments and clearances if you zoom in.
 
My baler does this same thing. Check the twine disk for wore grooves. Also check to make sure when hand operating the knotters that your needle swing arm is straight. I think the last guy who owned mine must have ran it over a rock pile and bent the swing arm crooked. After some grinding I got the needles to sit straight but one needle now goes farther up then the other. This causes the string on one side to be longer. Only fix is to find a replacement swing arm or bend the arm straight. One more thing massey's seem to like medium windrows with long stemmed grass. Grass too short will make long, loose bales and too big will make the notters fail to tie.
 
Thank you very much guys.

I had a bit of a hunch last night, and with what mr. Berry said before I left today, I went up to check it out.

OK, Imagine the box that the twine sits in. Open the door, and to the left of that box is the twine tensioner. The twine then runs through two springs.

The one spring, I noticed yesterday, was dangling. It was still attached but was not tensioning as it should have. I had no clue that something so "minor" could make any difference. Today I checked the tension both at the needles and up at the knotter and found that the right side was MUCH looser. Sure enough, that's the side that was dangling. I got a nice washer, put it on the bolt, and then clocked that spring the same as the other. The tension was then almost the same (to my weathered hands) so we gave it a try this evening after I raked the whole field.

That dang baler worked great. It knotted every bale, but one thing that we noticed: When we get to the end of a windrow, and are lining up for the next one, that machine working without any hay still managed to fail on one bail. That was 5 minutes after we started. I thought it was going to be a disaster all night,

BUT,


THAT BALER NEVER SKIPPED A BEAT AFTER THAT!!!!!!!

THE TWINE WAS VERY NICE AND EQUAL!

THE TWINE WAS AT THE SAME TENSION IN THE BALES!

I read somewhere on here that you want the twine to rise 2-3 inches when you lift the bale. Some of ours were looser than that but we were baling some crappy hay in spots and that's what I attribute it to.


There's no doubt in my mind this thing isn't "PRIMO" but let me tell you what, it got the job done for us!!!

My dad picked it up for $100 at a farm auction and it's been working nice.

He says its nothing near the machine our John Deere 14T is (we sold it to my uncle) but I'm sure it'll work for us. Heck, we only bail maximum 300 bales on our ground every year. We keep probably 50 bales for our selves for mulching purposes and then sell the rest to the neighbor.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top