FAS

New User
Hoping someone can help. Casting code for top cover in 2-26-z center section is 2-8-z The chassis no. is F 52,887
The engine is serial no. 8225 The block casting no. is 264347 R 3 Can you help me understand the numbers
 
Look it is HOW MANY years old and god only knows what that tractor has been thru . You would have a Stroke of my ugly 806 then . Or one 1066 in the neighborhood as both were involved in accident 's and busted in half and piecemealed back together , My 806 has a 706 center section , it has chain imprints in the fuel tank sheet metal . . I have personaly used 400 parts to repair a S/Mta that broke and axle housing while under a mounted picker , swapped out a center section of a 400 with a 450 fop a fast T/A repair . SOOOooooo casting numbers are NOT going to match. I had a buddy buy a S/MTA in KIT FORM that was a Johnny Cash special with a little of this from one tractor and a little of that from and other tractor and when all the bolts were put together he had a S/MTA .
 
those tractor were only built in 1954. so if you know you dont have a pieced together tractor you are good. the letter Z stands for a year so hopefully 54. i dont feel like hunting for the chart. each year has a different letter. mr. slater is the guy to see.
 
I would say the number look right, you can go into THE REGISTRY and lookup IHC scroll down to SMDTA their are 14 registired,another guy that been all threw the SMDTA is Jim Wharehime, form Maryland,hope i didn't misspell his name!
 
Can you post a picture of the serial number plate, the date codes seem fine, but accordingly to the book, it should start with 60,001, not 50,001 like i first thought, but the date codes seem right for about a March 1954 tractor!
 
Interesting, serial number plate indicates a SMD built in 54. Chassis serial number is higher than some information says, but a few 54 suppers have turned up higher. Other information you posted indicates it could be SMDTA parts. Never found a R3 block number in a SMD and I have looked at a lot of tractors trying to find one while trying to find a R2 block. Seems IH skipped R2 and went R1 to R3 or a R2 is a rare block. Always wondered if the R2 had a defect if produced. First official production SMDTA tractor was 60004. Big question is does the center housing have one bolt on each side showing retaining housing to transmission, or four bolts on each side? Thanks for any information you can give.
 
Other questions. Does the chassis number have any letters after it? Does the chassis number plate have a D stamped in it? Could the 5 at start of number be a 6? Don't know how plain the plate is.
 

cvphoto62884.jpg
 
If housing between engine and transmission looks like picture # 1 it is a t/a chassis. Part mainly in front of pulley gear box. If it looks like two or three it would be from a stage 2 SM chassis. Hard to be sure of things on plate.
mvphoto64818.jpg


mvphoto64819.jpg


mvphoto64820.jpg
 
Couple of serial plates pictured. SM gas, have a diesel but no picture it still has all the black. Only difference is the diesel plate has the D stamped in after the model SM and the F is closer to numbers than the gas one. F also is lightly stamped in with black on the F. Didn't think to check if gas one has the F stamped. Other picture is a SMTAD plate with all black gone. Most SM had a J for rockford clutch after the serial number. If tractor in question is a actual SMD with a legit serial number it may be the highest that ever turned up. Also late enough to have a IH clutch made almost like a rockford clutch with no ID letter used. Can't see a D on plate for diesel though. With no other information you need to ID a picture of housing.
mvphoto64830.jpg


mvphoto64831.jpg
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top