I have enjoyed metal casting since I was in the 8th grade back in 1964. Became a "shop teacher" stilll find the process fascinating.

Smelting is the process of extracting the desired metal from raw ore.

There is more to casting good parts than just melting some old cans and pouring the liquid into a mold. LOTS of variables come into play.

You might take a look at the Homemade Tools Forum. There are a few metal casting threads on there.

i have posted a few threads. These are somewhat detailed explanations of How I made a home foundry;

First furnace

Elements

Final Furnace

Casting parts

There are many more on the HMT site;

Marvellous tutorials ! Thank you.
 
I'm assuming these mower parts are outrageously expensive or obsolete, yes?
They are gage wheeles. They were $65 a few years ago. Last I checked a couple of years ago, they were $120 each. Simple wheels. I have repaired and repaired them. Time to do something different or break down and buy new. I will probably spend as much and a lot more work going this way. I rarely do the right thing but I will enjoy doing it. I wanted to do metal casting for years. I have a lathe,mill and a plan. Just not much time left. Maybe smelting is not the right term but that is what I have seen it called. Thanks for everyone’s reply.
 
They are gage wheeles. They were $65 a few years ago. Last I checked a couple of years ago, they were $120 each. Simple wheels. I have repaired and repaired them. Time to do something different or break down and buy new. I will probably spend as much and a lot more work going this way. I rarely do the right thing but I will enjoy doing it. I wanted to do metal casting for years. I have a lathe,mill and a plan. Just not much time left. Maybe smelting is not the right term but that is what I have seen it called. Thanks for everyone’s reply.
Where are you located? Do you have a pattern yet? Be happy to make you some rough castings if you want to finish them.

The thing that finally pushed me to build my furnace was the need for some spacers for the split rims to put wide lugged tires on my old Gravely walk behind.

To give you an idea of the reality, took about 800 pop cans for each spacer. 35 standard pop/beer cans is about a pound. But there is a lot of paint (labels) and a thin coat of plastic lining the can. Then some of the aluminum is lost from oxidation so you end up melting about 60-70 cans to get a pound of good aluminum.

One of my happy places is turning cans and broken aluminum into usable items.

If you already have a lathe and mill... you NEED a foundry!!!

Check this out;

My Gravely wheel spacer.

1790160879209.png
 
My nephews daughter is welding in high school. Does that count as metal shop class ? In fact she intends on going to a VoTech to continue her welding education.
I don’t if it does but kudos to the schools and kids that are doing this? Really impressive.
Side say,
I was so proud of my granddaughter (age 13) when she too welded the replacement top plate to the brush hog.

Side say ,1966 ,we were required to cast a project of our choice in shop class . Mine was the aluminum head to a finish meat tenderizer.
 
I don’t if it does but kudos to the schools and kids that are doing this? Really impressive.
Side say,
I was so proud of my granddaughter (age 13) when she too welded the replacement top plate to the brush hog.

Side say ,1966 ,we were required to cast a project of our choice in shop class . Mine was the aluminum head to a finish meat tenderizer.
Since we were casting lead in high school, I made a battery terminal mold out of mahogany and cast a lead battery terminal. Still have both.
 
I used car pistons as my source of aluminum to melt. the alloy is much stronger. Aluminum cans are way to pure aluminum and weak.
The Paperback books from Linsey were my guides to build the furnace, molds, etc to cast my metal turning lathe. When casting aluminum you need to account for a 3 percent shrinkage for when it hardens. Don't worry about making a mistake just remelt and recast. it only takes a few minutes.
Since the books are not available now. if you are serious give me a side e-mail and I will go down in the basement and look for them in the thousands of books I have.
 
I make a lot of bullets, and I’ve even casted lead toys for a friend of mine that had the moulds his granddad made his toys with (likely what’s wrong with him, I asked if he use to chew on them). Preheating the moulds, fluxing the mix. If I was going to try to cast anything, I’d start with lead for pratice since the melting temp is so much lower. A single drop of water into the pot can make your lead “explode”, so in addition to the safety wear, look out for water!
 
If you really want to explore casting ZINC is much safer option than lead. Many times what we call "pot metal" is actually zinc allow. You can easily collect zinc alloy from the cast parts on many common household items. Many times the "sculptured" handles on kitchen appliances, plumbing fixtures in the kitchen and bath. Also many automotive, motorcycle trim parts, etc, are cast from a zinc alloy.

At first glance zinc seems more expensive, $3700 per ton, vs $1888 for lead, but zinc is less dense at 7.13 vs lead at 11.34. So, cost per weight is higher for zinc, but cost per volume they are much closer.

You can melt zinc alloys with a propane torch in a steel food can or cast iron pot. I have made new wheel bearing for low speed

Low speed bearings like you might find on a NHS wheel and tires assemblies for yard equipment are often cast from Zinc Alloys. I have made new bearings for a yard cart, that I found in the neighbors trash, from zinc cast to to rough shape then machined to size.

If you enjoy making things, casting provides lots of options.
 
If you really want to explore casting ZINC is much safer option than lead. Many times what we call "pot metal" is actually zinc allow. You can easily collect zinc alloy from the cast parts on many common household items. Many times the "sculptured" handles on kitchen appliances, plumbing fixtures in the kitchen and bath. Also many automotive, motorcycle trim parts, etc, are cast from a zinc alloy.

At first glance zinc seems more expensive, $3700 per ton, vs $1888 for lead, but zinc is less dense at 7.13 vs lead at 11.34. So, cost per weight is higher for zinc, but cost per volume they are much closer.

You can melt zinc alloys with a propane torch in a steel food can or cast iron pot. I have made new wheel bearing for low speed

Low speed bearings like you might find on a NHS wheel and tires assemblies for yard equipment are often cast from Zinc Alloys. I have made new bearings for a yard cart, that I found in the neighbors trash, from zinc cast to to rough shape then machined to size.

If you enjoy making things, casting provides lots of options.
That’s interesting! I have a seemingly lifetime supply of old US made Babbitt ingots for bearings etc., but I’ve been discarding anything zinc to avoid contamination of my smelting pots. I’m going to try seeing what I can get Zinc to do with a hot plate or a torch. Seems like a good way to make jig weights that I want to “swim”.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top