The hitch is in

SVcummins

Well-known Member
Found some bits that really cut like a hot knife through hot butter a little antifreeze sure works good for cutting fluid to
cvphoto98113.jpg


cvphoto98114.jpg
 
Sv you better watch out Barney is going to come after you. That hitch isnt factory engineered, certified or licensed by the state but I like it anyway. Tony
 
If I posted this, I would be accused of making a death machine.

Local news
The truck in front was pulling an air compressor, which became detached and hit the front of mini van.
cvphoto98124.jpg
 
I hope that 3/8 bit was drilling a pilot hole. I'd want a lot more than 4 3/8 bolts holding a hitch down.
AaronSEIA
 
(quoted from post at 10:05:05 08/20/21)
(quoted from post at 10:37:12 08/20/21) These bolts are special grade 32 they are rated at 5000 pounds a bolt shear strength

Grade 32 must be top secret, lucky you were able to get them.
I'd have one more on the sides and two more front and back.
 
I don't think they are in properly to consider shear strength.
By the looks of it the 2 metals are not bolted together. looks like a gap between the plate and floor of truck. That will make it bend and break a lot easier than a shear.

I am not saying it won't hold 20,000 lbs but I also don't know what you are pulling on it.
If I have a trailer with 6 2000 lbs cattle on it plus the trailer and hit the brakes hard, (I never do that but...)what would be the actual weight pushing forward. Is it more than the weight because of speed or does it not change ?

Looks good except I have never seen such small bolts used.
 
In a prior post there was a picture of a torch cut hole kinda the shape of Texas that was for the ball shank :shock: . Happy that hitch is 1,500 miles away from here.
 

Maybe the ball shank goes thru the two plates and thru like an 8 inch channel iron crossmember???
That has been added under the bed which has end plates bolted into the frame webs???
 
1/2 grade 8 bolts . 4 bolts the same as hold a b&w hitch in . The plate is one inch thick actually thicker than Ive used before not planning on hauling to much and none of my cattle weigh 2000 pounds are running chania?
cvphoto98189.png


cvphoto98190.png
 


Every B&W turnover ball hitch I have ever seen has four 5/8 inch dia. Bolts into the crossmember for 3/4 ton Dodge.
And six 5/8 inch bolts going into the crossmember for one ton Dodges.

Half inch thick bar stock welded 50% or less to some half inch plate does not make one inch plate.
Plus the rule of thumb for bolted plate connections is the bolt should be 1.5 up to 3 times the thickness of thinnest plate.

Those d-rings must be the 3/4 inch diameter ones if those are welded to 1/2 inch plate.
 
Amazing how much stuff accumulates in a pickup bed. If I want to use my Dodge ram to haul something, other than my trailer, and tractor It's a major cleaning operation. Then I need to find a place to put everything. Stan
 
The b&w hitch for this truck bolts with 4 half inch bolts for the
side rails and four to bolt the hitch plate to the sidle plates
which are 1/4 inch thick . They are one inch d rings
 
Not sure of the rules, but I imagine that the trailer is never suppoded to disconnect in case of a rollover, so your hitch support must be able to rollover your truck, lift it, etc, with some acceleration to it (maybe 3G, so there times the weight).
Same goes for accidental braking. If you were to survive a front impact, you do not want your trailer to detach. Your connection needs to be strong enough to crush the front of the dodge by pushing on the ball hitch. It is obvious that 4x 1/2 inch are unsafe.

Some cross tubing welded to the plate would really help avoid flexing of the plate.

You need to have good contact between plate and chassis, or your bolts will fail . Bolts are failing due to repetitive excessive stress variations. Longer bolts mounted with solid spacers are better than short bolts.

2 piece of drilled sheet metal inserted between the bed ribs were the bolts are sticking to the chassis will really help: as you tighten, you want to elongate the bolt and have solid connection. You absolutely do not want to crush the bed ribs partially as you tighten. the ribs will continue to crush with loads, loosening your bolts.

Loose bolts have excessive stress variation everytime they are under load and broke quickly.
 
I made solid spacers between the hitch and the frame rails so
the hitch is not supported by the thin sheet metal cross
members supporting the bed
 
And what would you bolt them to the 1/16 inch thick sheet
metal of the bed ? Have you ever looked at a truck frame ?
 
My hitch doesnt need bolts to hold the hitch together
Because its one solid piece not 5 pieces like b&w if you
hadnt noticed so I have the same 4 bolts holding hitch to
frame as they do
 
Have you ever looked at a truck frame ?

Yes I had a 97 Ford F250 powerstroke for almost all the 5 years I lived in Kansas. I miss the ultra fast governor response while the e40d was shifting up and down. I taught this was quite unique and impressive from the first common rail diesel.

Mine did not have a goiseneck hitch but I tought making one so I could rent a bigger trailer. My plan was to remove the bed and put the support under the bed. Your way is much simpler but on mine the bed was attached to the chassis with rubber mounts, so it would have been difficult to sandwich chassis and bed.

It is your truck and you are excellent driver.
But as a mechanical engineer, I have to warn you against what kind of forces that may be applied to your hitch.
Now, if you are as strong as others, do not worry. And checking bolts tension after 10, 100, 1000 miles is always a cheap insurance...
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top