Thought I'd Lost An Engine!

Allan in NE

Well-known Member
Oh Man!

I've got a tractor with One Weird Problem.....The darned thing will hydrolock.

Engine is a 301 gas out of an 806. Just runs like a clock.

However, if I don't routinely remember to tighten that exhaust pipe with a pipewrench and it should happen to rain, water will seep in around the threads on that big exhaust pipe and fill the cylinders with water.

Tractor has been sitting for a couple of months and it took me 3 hours yesterday to get the goofy thing dried out and running. Thought fer a time there that I had bent some valves 'er something.

Don't quite know what to do about it neither. :>(

Allan

22.JPG
 

Well, Alan, I don't know of any solution except to put it under a shelter. Or maybe put a small piece of plastic at the base of the exhaust pipe and tighten it with wire, remembering to take it off before use. Or put a long enough small barrel over the muffler.

KEH
 
Glad you were able to get it cleared up. Didn't you have that engine overhauled recently? Would have been a shame to loose it!
 
Naa, Don't you know what old farmers do in cases like this? they grab the old buzz box and nickel rod and fix it so it can never be fixed right again.
Actually I think there is a JB weld, or something like it, that is good for exhaust temperatures.
Kenny
 
I have a Ford that would do that, I removed the pipe, found an adapter that went from the size of the pipe to one inch larger, welded it to the pipe just above the manifold, sort of acts like an umbrella and moves the water out away from the threads, never gets wet anymore. I don't have any red tractors so I don't know if you have room for that, but it is easy and simple.
 
Build a machinery shed. My late dad was stickler
on putting everything back in the machine shed.
We only left the combine & tractor out when combining. When we were finished with the trailer type plows we would brush on used engine oil over the moldboards, landslide & plow point.
If they were worn we would replace as needed before putting them in the machine shed. The only thing I leave out now is my old metal wheelbarrow. I've had to replace the handles & wooden pieces a few times. It's about 40 years old. I have contractor type with dual wheels, but its buried back in the garage. A person should move about every 5 years so you don't accumulate so much stuff. Those cattle will enjoy that hay when snow starts to fly. Hal
 
What about the pipe dope that plubers use on hot water pipes on furnaces and boilers? That stuff is pretty high temp as well and if it can seal water from getting out, it should be able to seal it from getting.
 
Al, You need to do like I am doing. Just donate 50% of your farming profits to Al Gore's save the planet fund so that global warming will go away and we won't have constant rain. Haven't you noticed how nice the weather has been getting recently?
 
allan, napa has an exhaust sealant that comes in a tube like silicone rtv. the stuff is kinda gritty. this stuff works real good. i used in on my minnie moline to fix the exhaust ports on the cylinder head to manifold. the old manifold leaked for years before i got the tractor, the the machined surface was all boogered up. still holding after 5 years. also works good on the pipe to manifold threads when the threads in the manifold wear out. glenn
 
Allan Howdy! Neighbor. Have you tried leaving the stack loose, then run the tractor till it get good and hot, to expand the metal a scosh then retighten?
Or take the stack out, run to hot then reinstall! Just a thought Hope your baling goes mostly uneventful.
I you get too much rain later and have some left over send it south If you would. LOL!
Hope you get it to stay put.
Later,
John A
 
Allen: Haven't tried it personally, but I know POR-15 puts out a Fire Seal epoxy that might do the trick. Like all of their products, it's spendy, but $20 is cheaper than an overhaul, and all of their products I've used have been well worth the cost.
Fire Seal epoxy
 
My wood stove flue pipe has a rain collar on it where it exists the roof connector. Keeps the rain from running down the flue and into the houde/stove. It uses high temp RTV sealant between the flue pipe and rain collar. Flue gets pretty hot cause it a short run to the roof and the rtv saelant has never burned out. So like the others said try that rtv sealant, I think it is rated good to 650 degrees.
Pete
 
I would probably try some high temp anti seize as a sealant as well as a way to remove it in the future for replacement. I'm not sure it will work but that and a spot braze to hold it from backing out should do the trick.
 
Had that happen to my 450 Farmall a few years ago. Just glad I did not send my boy or brother over to the field to get it or it might of needed a overhaul. I try to keep everything in a shed. Brother is just the opposite. Right now all kinds of shed room and four tractors setting out.
 
How about making a sheet metal collar that fits over the pipe, and directs the water off to the side- like an umbrella with a hole in the center? Fits on the pipe, under the wider part of the muffler.
 
Yep who had the bright idea to make manifolds that way? The high temp anti seize and collar shield are good ideas. If threads are rusted and rotted out it will never stay tight so on those I've fixed some permanently on Wisconsin and Continental engines by welding a short pipe nipple in with nickel rod then sleeve the muffler over that and clamp it. Stuff some steel wool in hole you can pull back out after welding it so sparks and slag don't get down in engine.
 
If the threads are OK in the manifold, I would take out the pipe/muffler and weld a washer like flange on it just above the threads (maybe 1/4" above the spot the threads stop in the manifold. It should be just as big as will fit down through the hood hole. Silver anti sieze will also reduce the flow. Jim
 
You either have an awful large crack in the threads or its getting in from somewhere else. I would poor water on it to see if it is actually getting in at the threads.
Walt
 
Allan, sounds like your darn lucky your not soaking that engine in wonder juice trying to free it! My experence with water in a gassers cylinders is it rusts things up pretty fast. Sealers are not going to work because of the heat. Best thing would be get a new USA made pipe and crank it in tight as you can then weld it with the nickel rod. Your not ever going to need to remove it anyways.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top