what alternator?

74JD140

Member
im thinking about putting a car style alternator on my 1950 Deere A and i wasnt sure which one to use. ive been told any 1 wire gm alternator will work. if this is correct and i can use any 1 wire alternator, how do you go about hooking up the amperage gauge? if you just run the charging wire through the amp gauge, will it make the gauge work and still charge the battery? thanks
 
There's NO SUCH THING as a "ONE-WIRE GM ALTERNATOR", in the common automotive sizes. The one-wire alternators are AFTERMARKET ABOMINATIONS.

If you jump down a few threads, you will find the post below that shows the basic wiring for a 10SI or 12SI 3-wire Delco alternator conversion.

Using the REAL DEAL, a 3-wire setup is an especially good idea on Poppers, where there is a small drive pulley on a relatively slow-turning fanshaft.

<img src = "http://i167.photobucket.com/albums/u125/27Grainfield/424IH/Alternator%20Stuff/AlternatorHarness41.jpg">
Do it RIGHT
 
ok, forgot to mention, my tractor has no wiring on it at all right now. i have to completely rewire it. so my question is... if the one comming off the stud goes to the battery for charging, does the other one with the diode go to the amperage gauge? i still dont understand how the gauge gets hooked up.
 
A "HOT" wire from the battery-side terminal on the starter switch goes to one side of the ammeter.

ALL electrical loads (ignition and lighting) AND the wire from the output stud of the alternator go to the other ammeter terminal. If the meter reads backwards, swap the connections between the terminals.

The "excite wire" to the alternator's #1 terminal is fed from the LOAD side of the ignition switch, and you MUST use the diode (as shown) or a resistor or an "idiot light" in that lead.
 
Is your 1950 "A" equipped with a magneto?

If so, you can use a simple 2-terminal NO "closes at 4 PSI" oil pressure switch to switch on the "excite" voltage when the tractor starts.
 
this is the alternator im looking at. its a real one wire alternator with a "self energizing" regulator. if im understanding this right, i would take the one wire from the alternator along with the wires from the lights on my tractor and put them on one side of the amp gauge, and then wire from the positive side of the battery would go to the other?
 
First as previously mentioned, do not, do not, do not use one wire alternators. They are marginally good on tractors that turn over at 2000 rpm, not on a deere 2 cyl and 3 wire cost about a third as much and the regulator/rectifier will last 3 times as long. Ask for a mid to late 70's v8 small block chevy alternator from your local discount auto store, should cost under 50 bucks.

But why use an alternator? First, a mag JD needs only to charge for the power that the starter motor uses. If your tractor doesn't start almost instantly, well you have problems that an alternator won't solve, starter motors are expensive to replace.

Second, on this site there are parts sold to easily fix the generator. Most of the time it is just the brushes stuck or worn. Search for generator repair kit Part No: GRK106. 14 dollars.

An IT manual should show you how, take 20 min once you have done it a time or two, an hour your first time. Might need and extra hand to hold the brushes out when reassembling the first time.

These kits include brushes, bushings, and bearing to rebuild your generator. Most often the windings are fine. Replace your regulator, and make sure your wiring is in good shape, especially the main battery cables. I completely rewired an A not long ago, new regulator, new cable, new wires, and rebuilt the genny for under 100 dollars. I shouldn't of put it off so long, now charges like a champ and doesn't look stupid with that aluminum housing setting out there.

Also remember you will need to jerry rig some type of brackets if you change to an alternator.
 
Yes, they make such a thing, doesn't mean it is a good Idea, they have to turn a certain RPM before the self excite and they are not very durable in my experience with multiple tractors. Everytime I have been asked to repair a tractor with a malfuntioning single wire alternator, it was placed there in attempt to cover up a problem some where else in the system. The only place a 3 wire alternator is a good idea in my opionion is if you are using alot of field lights that a generator just doesn't have the output for. Do you have 6 or 8 field lights and using the tractor to plow all night?
 
i have 3 lights on the tractor and no it doesnt get used alot at night. i really wanted to get a generator to put on it but i cant find any for sale at a decent price. i dont need a new or rebuilt one, just one that works.
 
i dont have a generator to rebuild. my tractor didnt have one on it when i bought it. if i had one i would rebuild it. thats why i said im looking for a decent on to buy. about the 1 wire alternators, i was going to put a bigger pulley on it to make it spin faster in relation to the fan shaft. but the only thing i dont like about that is, like you said, the big ugly aluminum casting hanging there. i would much rather have a delco generator. what is the delco number that is supposed to be on my tractor so i can further my search for one?
 
JD, I would prefer a Generator if you want to keep it original but my choice of an alternator would be the GM 10 SI 3 wire internal regulated because its so cheap n readily available,,,,,If wired as the pic shown below it can excite at low RPM versus a 1 wire which can require higher RPM.

That alternator requires Neg ground so you have to switch from the original Pos ground.....If you switch polarity the ammeter leads need swapped otherwise it will register bass ackwards......No wiring changes as far as any Magneto ignition is concerned, its NOT connected to the battery........

The alternators big rear output post/stud wires up to the Load (NOT battery/starter) side of the ammeter and I would use 10 gauge wire.

If you had lights, the light switch would receive its BAT INPUT VOLTAGE from the same load ammeter terminal that wires down to the alternator......

The ammeters other SUPPLY TERMINAL (NOT one that wires to alternators output or feeds light switch) connects to the hot ungrounded battery post usually via a wire (Id use 10 gauge) from the ammeter down to the starter switch where the big battery cable attaches. Theres usually only one wire on that SUPPLY TERMINAL while the ammeters other LOAD TERMINAL is what wires to the alternators output and feeds voltage to switches.

If theres no ignition switch like on mag ignition tractors you still need to excite the alternator (like the ignition circuit does on coil distributor tractors) so some people use a normally open oil pressure switch contact to serve that purpose.

If you replace the genny with an alternator, the wiring diagram above changes. Again the alternators rear output stud/post wires to the ammeter (replaces wire from BAT on VR to ammeter) and the light switch now gets voltage from the ammeters Load terminal (replaces wire from L on VR to light switch) PLUS CHANGE POLARITY TO POS GROUND which means ammeter leads are reversed.

Hope this helps.

John T
A-3-JPEG.jpg
 
but what if i get a generator to put back on it... will i still need a switch to start the charging or are the delco generators self exciting?
 
If you use an original Generator and Voltage Regulator (BOTH are required) it will wire as shown in the diagram and the genny will work n excite with itslef and the VR, you DO NOT need any other sort of switch at all like on a alterntor that requires excitation, either via an ignition switch (for coil ignitions) or an oil pressure switch set up on mag ignitions.

John T
 
Yes, it is, to a point.

If generators have been apart for repairs, or have sat unused for a LOOONNNGGG time, they may need to be polarized to restore the residual magnetism in the poleshoes.

This residual magnetism is what makes them begin to charge at startup.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top