Where do i fill the loader hydraulics??

WILL1E

Member
My '55 Ford 850 has what i've been told is a Wagner front loader on it. The 2 main lifting hydraulics have slow leaks where the rod extends out of the housing. I've noticed lately that some of the movements have been getting jittery so i'm thinking the fluids are getting low.

I've been tracing the hoses all around, but it seems like it never goes into the tractor anywhere except for where the pumps hangs off the front below the radiator. There are a couple points where hoses appear to terminate into the frame of the loader...is it possible the fluid is contained with the loader frame??? I did notice on the passanger side of the loader frame near the top there appears to be a cap of sorts. Is that where i fill it?

Also, are there any tips/tricks to filling it with hydraulic fluid? Or do i simply open the cap and just fill till it starts coming out?

nvd0UWel.jpg

CWnStjCl.jpg

Qt8wFEtl.jpg

g9BhBNrl.jpg
 
(quoted from post at 07:55:28 06/22/21) ..... I did notice on the [b:b3741a0eb4][i:b3741a0eb4][u:b3741a0eb4]Right[/u:b3741a0eb4][/i:b3741a0eb4][/b:b3741a0eb4] side of the loader frame near the top there appears to be a cap of sorts. Is that where i fill it?
Yes. That is also a breather. Unscrew it to fill.

Also, are there any tips/tricks to filling it with hydraulic fluid? Or do i simply open the cap and just fill till it starts coming out
Fill until it is about 4 to 6 inches below the fill pipe. If you fill it too full it will come out the weep holes at the top apex of the curved frame, when lifting high and/or lowering from high. These holes are usually on the inside of the frame on both sides of a Wagner.

You really just need to be above where the suction line comes off the frame, at all times. Filling to 4 to 6 inches below the fill pipe assures that.

You will also notice a screen filter where the suction pipe attaches to the frame. Good idea to check this at least once. I've seen them clogged, restricting flow to the pump. If you clean it, should be good for many many years.
 
I had the same issue when I first got my tractor. I figured out the model number of the loader, and found a copy of the manual online. It showed where all the parts are. Filler on top of the loader mast and drain plug on the bottom. And mine specified to fill it 8 from the top.

My loader takes 10 gallons of hyd fluid, and I really need to change it one of these days. I think its been around 10 years.
 
Thanks everyone!

So do i remove the reducer and everything above it, or do i remove whatever is above the reducer?

4-6" down....do i fashion some sort of dipstick to know that the fluid is at that point?

Screen filter...is that the Y shaped silver thing in my bottom photo? Can i clean that with all the fluid in the frame or do i have to drain the system?
 
(quoted from post at 08:50:19 06/22/21)So do i remove the reducer and everything above it, or do i remove whatever is above the reducer?
emove whatever want's to come off. Bigger opening makes it easier to fill. Might wanna clean the breather while your at it.

4-6" down....do i fashion some sort of dipstick to know that the fluid is at that point?
up. Welding wire, mechanics wire, coat hanger, etc. just get it approx.

Screen filter...is that the Y shaped silver thing in my bottom photo?
es. Where the suction pipe attaches to the frame

Can i clean that with all the fluid in the frame or do i have to drain the system?
rain first. Your call whether or not to clean it.
If you do, drain from the absolute lowest point. Then try to get more out. That's where the water is if there is some.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top