Why do floats stick

SDE

Well-known Member
I had it happen twice on my other 400. Both times I had to pull a plug to drain a cylinder. I think I will remember to pull the coil wire, if it happens again. On this 400 I had lost the cap that covers the overflow drain in the carburetor bowl, and so I installed a vent from an air cylinder. When I got back to the tractor it was peeing onto the ground, instead of filling a cylinder. Is it almost always crap in the needle valve or is it the float itself that needs to be reshaped due to fatigue?
TY
SDE
 
Shut off the fuel at the tank or elsewhere if there is a shutoff valve.

Can be crap in the fuel, needle problems, float filled with fuel, float rubbing side of carb and sticking, or lots of other things.
 
#1 you should always shut the fuel off when you park it. Or you can end up with an oil pan full of gas/oil mix and then blow an engine.
#2 a float it self can be bad and cause that.
#3 dirt/rust in the needle seat can cause that
#4 a float set wrong or hitting the sides of the carb can cause that and a few other things
 
I shut the gas off and got it restarted. It only ran for a short time before I ran out of gas. As I was putting more gas in it, it started to overflow out the carburetor again. That is when I called it a day. When I take it apart, I would like to get it fixed on the first try.
TY
SDE
 
Like Old recommends I was taught at an early age to ALWAYS shut off the gas when finished for the day. Eliminates the possibility of filling the crankcase with gas.

I too have experienced intermittent float sticking. Most often it is a worn float pivot bracket, or a poorly made replacement float. But this also happened to my Minnie Mo U:

Ran it out of fuel once. Just as it quit it suffered a particularly explosive backfire - so violent it actually blew the hose off the carb air inlet.

Afterward the carb would randomly and unpredictably flood. After struggling with it a couple weeks I disassembled the carb. Problem turned out to be partially flattened carb float pontoons. Apparently the explosive pulse through the carburetor was powerful enough to flatten the floats slightly so they would randomly rub and hang up on the (rough) float bowl wall.

A new replacement float fixed the problem.
 
Ok... I turned the tractor off. I went to the house to get a drink of water... SHAME on me for being so thoughtless as to not turn the gas off for the 7 minutes that it took to get the water. So here is what I am going to do. I will remove the bowl, and then turn the gas back on. I will gently raise the float. If the gas does not shut off, then there must be debris in the needle valve. It it does shutoff, then the float must not be able to move in an unrestricted manner and i will look for what is causing the restrictions
 
Most carbs have a screen in the inlet fitting where the fuel line connects, the last stop before the needle valve.

Should also be a screen on top of the sediment bowl, and a screen standing up inside the tank where the sediment bowl screws in.

Even with all the screens in place, a trashy tank will still manage to get something in the needle valve, it only takes a tiny speck of rust.

Other causes are a partially sunk float, a loose or damaged needle valve (especially the rubber tip, it can be damaged by rust flakes getting embedded into the rubber), the float touching the inside of the bowl, or improperly set.

If you end up going into the carb, before putting the bowl on, turn the body upside down with the weight of the float on the needle valve. Suck on the fuel fitting, put your tongue over the hole. If it won't hold vacuum, it will not stop the fuel flow, something is leaking. Be sure the float tab is pushing the needle and not bottoming against the end of the seat, also be sure the needle is not binding inside the seat. Aftermarket parts are commonly not exactly right. Easy to burr the brass seat with a screw driver when tightening it.

Once the tank is clean and all screens in place, be sure to blow out the line. I like to turn the gas on, let it flow a few seconds to flush any debris out of the line. You can even leave the gas running while connecting the line to the carb, especially if the area is caked with dirt.

Since it flooded over in the short time it was left on, the problem should be fairly obvious. That is a substantial leak. It was probably not running well, too rich.
 
I took the bowl off with the gas on I could gently raise the float and the fuel shut off nicely. I put the bowl back on I used the tractor for at least 5 minutes and it isn't peeing fuel. So I will chalk it up to GREMLINS at Large
TY
SDE
 
Everyone thats replied gave very good advice and I would like to recommend using only non-ethanol gas if youre not using it regularly and it sits for a while. Years ago before I went strictly to non-ethanol fuel I would have carb trouble with floats sticking due to the gas gumming up the carb , Ive got too many tractors that sit for long spells without being used so thats the way I go.....
 
well these tractors came with a fine screen that sits in the top of the sediment bowl under the gasket. plus there is another screen at the carb inlet. and thats it, there is no screen on the stand pipe in tank. so that means with those two screens there is no reason to worry about junk getting in the needle valve. its been that way since the tractors were new. first thing that happens is people throw away the sediment bowl screen. only the bigger stuff will settle out in the bowl. the rest goes straight to carb screen which was the secondary catch screen. technically anything going through that screen will not cause needle valve trouble. as your needle valve and jets are bigger. there is no reason to be closing the sediment bowl valve just because your thirsty. closing the valve is for when tractor will be sitting for long periods. so if gremlins did that you dont have your proper screens in place. plus on the cap it says buy clean fuel keep it clean. plus any rust in the tank is not the tractors fault. i am sticking to my tryed and true method.
 
one more tid bit of info ... once you have the line on and bowl cleaned it is always a good idea to open the bowl valve and give the line a flush before hooking it to carb. many times you can have a speck loosened just from doing your thing then this spec gets into the carb giving you a problem, but as i said carb screen should catch it but thats only if the carb screen is not damaged and well seated at the end.
 
There are two ways a float will not stick and yet overflow the carburetor.

On most gas tractors the float is brass. My cousins Farmall Super C had a problem and drained the entire tank. The cause was a pin hole in the brass float. A little solder and it was good as new.

I don't know whether they ever did this on tractors, but on some cars they went to a polymer (closed cell nitrile nitrophyl) float that can become gasoline logged. They start to float less and then this floods the carburetor. Some other floats are made of a hollow shell of a hard plastic like nylon.

Then there is always the possibility that the needle and seat are worn. The best way to test is to remove the bowl and gently raise the float until it is parallel to the body and see if the gas flow stops.


.
 
I understand SDE's thoughts. If you can't get a drink with the gas left on it must be a real problem. Our H sets for days on end with no problems and I don't remember ever shutting off the gas even when I haul it up to the bridge for the drive it is left on. I guess I'm either blessed right or you guys have some real p poor carbs and sediment bowls.
 
Gum and varnish or corrosion or foreign material are possible causes of sticking needle valves, maybe from setting too long, or old stale gas etc. For long term storage Ive had good luck using Sta Bil and a bit of low ash combustible two cycle engine oil in with the gas for long term storage.

Obviously if there's no gas left in the carb bowl and you turn off the gas to run till the engine dies (or drain the bowl manually) the float will drop down and the needle valve will be open, but if it gets stuck open/down and fails to rise and close, the carb will flood when the gas is turned back on grrrrrrrrrrr Soooooooooooooo if you drain the carb or turn off the gas so the float drops and the needle valve sits there OPEN just hope it doesn't gum/varnish stick and reman open when you turn the gas back on !!!!!!!!!!!!!!

Try Sta Bil and two cycle oil that can help sticking needle valves

John T
 
do grannie on the hillbillies... throw some moon shine in the tank! oops its rumatize medicine she would say.
 
I put 12v solenoids on mowers and tractors. This is a cheap solution to leaking carbs. Cheaper than
cvphoto90505.jpg

Find a tank of gas on floor.
No brainier to, turn key off, gas is shut off.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top