For Sale: $1,500.00
1893 Case Shaft Driven Threshing Machine. 12 Horse Sweep Power with all accessories. Good Condition
1893 Case Shaft Driven Threshing Machine. 12 Horse Sweep Power with all accessories. Good Condition
-
J
J.D. Douglass USEDPARTSGUY J.D. Douglass wrote on USEDPARTSGUY's profile.
I have spools here in Texas Wichita Falls
-
Kentucky Gardener phillipd Kentucky Gardener wrote on phillipd's profile.
long time no hear, hope you are well.
beckham
beckham
Half tracks for my Ford 8n. I am wondering if someone has or could make A pair of the specialty brackets for the fenders?.
Attached photos, with the part I would like colorized. Many thanks for any assistance from anyone. Hope someone may be able to assist. Sincerely. Richard Lewis. 🕊
Date of Writing this request: October 22, 2026
Attached photos, with the part I would like colorized. Many thanks for any assistance from anyone. Hope someone may be able to assist. Sincerely. Richard Lewis. 🕊
Date of Writing this request: October 22, 2026
Attachments
-
E
Eva58 Morgan Flowers Eva58 wrote on Morgan Flowers's profile.
Seen your post that you had a few years back about your Ford 4000 steering cylinder parts. How did you get it off the tractor? My husband is pretty mechanically inclined but cannot figure this out yet
-
T
trewgtregg da.bees trewgtregg wrote on da.bees's profile.
on a similiar note....when changing the 6v coil on my naa, is there a certain way the wires hook to the 2 posts on the coil? i dont see any identyfying marks on the coil. but my points did burn up ,and they wer new!
looking for advice on tire size? I have a oliver super 88 running 15.5x38 firestone tires on 16 inch 38 rims. dyno tuned 75 hp. Spinning out all the time. Hard track,soft track,long chain, short chain. Run 3.5to 4 mph. 18 to 20 inch draw bar height. would moving to a bigger tire help?
-
Tony in SD DotsonB458D Tony in SD wrote on DotsonB458D's profile.
Thank you. I email him.
-
T
Tom Feldpausch in MI NormanSavesTractors Tom Feldpausch in MI wrote on NormanSavesTractors's profile.
Hi, Norman.
Please ban this duostunsail...another scammer!
Thank you!
Tom
Please ban this duostunsail...another scammer!
Thank you!
Tom
-
Tall T ChrisFromCLE Tall T wrote on ChrisFromCLE's profile.
What does CLE stand for? Cleveland?
I just replaced three rollers on the crawler and need hydraulic fluid. I heard that AW-46 mineral oil will work for this. My hydraulic reservoir is isolated and not connected to tranny. Any issues I should know before purchasing?
-
L
Lynerd Mnethercutt Lynerd wrote on Mnethercutt's profile.
Mnethercutt Little over $400 from Deere. Lynn
-
P
peteL LPgas only peteL wrote on LPgas only's profile.
It is ok with me. I found this picture while surfing the internet and it amused me being an ex marine engineer.
-
C
craig rus Case Nutty 1660 craig rus wrote on Case Nutty 1660's profile.
I see you answered Case 580 ck questions.......when i push the dump valve pedal down, the clutchs spin, when i release the pedal, it stops, when i move the foward and reverse shuttle lever, I can kinda see oil squeezing out from between the clutch discs, but they do not turn..
Looking for help replacing front end grease seals on my 1946 Allis Chalmers model C. Tapped the new seal on, then the inner wheel bearing, but when I tried to slide the hub on, the fit was too tight, to the point where when I pushed on the hub a little harder, the seal moved back. Tried tapping it into the hub but that only made it rotate with the hub instead of staying stationary and the hub. What am I doing wrong
Got the C135 back today, crank came out standard all the way! Engine builder put the sleeves in (held them down with a bolt) and put the pistons on the rods. Everything got balanced, one rod way light and they all got brought down to the same weight. Engine is on a stand now, need to get new bearings and other bits and pieces. Anywho, its back, no major issues, should be smooth sailing for the most part.
-
N
Non-farmer MikeFoley Non-farmer wrote on MikeFoley's profile.
Hi Mike, and welcome to YT 
I only see these profile posts. You should post a thread here - that will get noticed more easily.
I only see these profile posts. You should post a thread here - that will get noticed more easily.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy