2010 Gas

[Nzak]

I have a 2010 that been sitting for 4 plus years.
i’m trying to move it without starting.
i‘ve tried pulling it with another tractor and it will not move.
can’t find neutral Shifter on right
any help would be appreciated.

 

[scootergmc]

Well anything could be stuck. What have you eliminated? Need more info.

 

[Nzak]

Well anything could be stuck. What have you eliminated? Need more info.

I’m thinking that maybe I’m not putting it in neutral to move.
very confusing shifter on steering dash.
don’t have experience with this tractor.
i’m an Allis Chalmers person.

 

[wore out]

I have a 2010 that been sitting for 4 plus years.
i’m trying to move it without starting.
i‘ve tried pulling it with another tractor and it will not move.
can’t find neutral Shifter on right
any help would be appreciated.

Go to the site linked below and find the Operator's Manual for your tractor. It takes a bit to figure it out, but you can view or download the OPERATOR'S MANUAL for free,

That should provide details on the operation of the shifter.

Many DEERE tractors must have the shifter in the TOW position if you plan on towing it more than a couple of feet to avoid severe transmission damage, I don't remember if that applies to the 2010, but the manual should cover that.
https://techpubs.deere.com/en-us/Search/Equipment

 

[Tx Jim]

2010 gear shift pattern is much simpler to understand than other JD rowcrop tractors of similar era. Be sure selector is placed in "tow position" before towing tractor very far. Tow position is between 6 & 7 speeds.

.

 

[NDIHC]

Isn't this the shift pattern? Sorry...couldn't resist!

 

[used red MN]

2010 gear shift pattern is much simpler to understand than other JD rowcrop tractors of similar era. Be sure selector is placed in "tow position" before towing tractor very far. Tow position is between 6 & 7 speeds.

View attachment 117266.

In the attached link is a clearer photo of what Jim is showing you above.
JD 2010 Tractordata trans info

 

[Tx Jim]

Here's the more clear photo of the 2010 RC shift pattern that URM referred to.

 

[Nzak]

Still can’t get it to move.
found manual.
trying to get it started.
just runs down battery.
cant get choke to move so working on this.
nice jd put up against engine where not easily accessible.
because it is positive ground anyone know how to hookup charger.
I’m thinking positive of charger on chassis
and negative of charger on positive post of battery.

 

[JIM MN]

Pull the gear shift lever down and leave in the left rail. If going any distance, pull lever down across from TOW? This puts the transmission in neutral at either positions. Make sure both brakes are released. You should be able to move the tractor.

 

[redtom]

Still can’t get it to move.
found manual.
trying to get it started.
just runs down battery.
cant get choke to move so working on this.
nice jd put up against engine where not easily accessible.
because it is positive ground anyone know how to hookup charger.
I’m thinking positive of charger on chassis
and negative of charger on positive post of batter.

Positive to positive no matter what

 

[Jim.ME]

Positive to positive no matter what

And if boosting with another Unit (car, truck, tractor, etc.) make sure the two are not touching as contact can be made through touching metal.

 

[used red MN]

Positive to positive no matter what

Meaning positive polarity of battery charger to positive terminal as indicated on the machines battery. Yes, positive of charger to the chassis.

 

[NDIHC]

Still can’t get it to move.
found manual.
trying to get it started.
just runs down battery.
cant get choke to move so working on this.
nice jd put up against engine where not easily accessible.
because it is positive ground anyone know how to hookup charger.
I’m thinking positive of charger on chassis
and negative of charger on positive post of batter.

Positive ground would require positive battery charger clamp to chassis or positive post of battery. Negative clamp of charger to negative battery post.