Water in transmission

Twisted_Steel

Member
Location
Monroe, NC
My neighbor has a 1957 Massey Ferguson. He checked his hydraulic fluid and it is yellow as all get out. We've drained the fluid.
I replaced the busted rubber boots on both shifters, so that should stop the water getting into it. He says he'll store it over the winter in a shed.
What's the best way to get as much contaminated fluid out of the tractor as possible?
I told him I'd ask here before we go pumping varsol or diesel into it.
 

Attachments

  • 20261119_163245.jpg
    20261119_163245.jpg
    1.2 MB · Views: 0
My neighbor has a 1957 Massey Ferguson. He checked his hydraulic fluid and it is yellow as all get out. We've drained the fluid.
I replaced the busted rubber boots on both shifters, so that should stop the water getting into it. He says he'll store it over the winter in a shed.
What's the best way to get as much contaminated fluid out of the tractor as possible?
I told him I'd ask here before we go pumping varsol or diesel into it.
Take it out and work it, get it up to temperature then drain it and leave it overnight.

Does it have a loader or is it a bare tractor? Multiple changes may be required to clear it. Working it and getting it up to temperature regularly to evaporate water out of the fluid off will help. Short runs and weather changes will add condensation.

Adding diesel or varsol can leave pockets of those in place of the water, they will thin the oil as well.
 
No loader just a bare tractor. We've already drained the oil/water combo out.
He's 77 and fixed income. He bought 7 gallons of 85/90 @ $135.00 today and can't afford another hit like that.
I have a sprayer that hooks to my air compressor and pulls fluid out of a jug. Is it possible to spray gas into it to wash it out and let the gas evaporate?
Here's a pic of the dipstick. The first post shows the oil in a tote. It looks like a sheet of cardboard laying in the bottom.
 

Attachments

  • 20261118_195050.jpg
    20261118_195050.jpg
    1 MB · Views: 0
What model 1957 Massey Ferguson?

I expect straight 80 weight mineral oil would have been the original spec as the transmission is the hydraulic reservoir. If he has been running 85W/90 for years just dump it in and go. What little contaminated oil remains in pockets will spread through the new, anything you spray in will stay in those pockets and mix with the contaminated oil in them. I would rather dump 3-4 gallons of cheap engine oil in it run it for a bit, cycling the hydraulics then dump that out and see how milky that comes out. Just my opinion and thoughts, others will differ, no problems each to their own.
 
Don't think I would add gasoline to the transmission. It could damage the seals.

I have used cheap straight 30 weight engine oil a few times. Fill it with oil. Work the tractor lightly until it's warm then drain. Repeat. Then fill it back up with the oil it calls for.
 
What model 1957 Massey Ferguson?

I expect straight 80 weight mineral oil would have been the original spec as the transmission is the hydraulic reservoir. If he has been running 85W/90 for years just dump it in and go. What little contaminated oil remains in pockets will spread through the new, anything you spray in will stay in those pockets and mix with the contaminated oil in them. I would rather dump 3-4 gallons of cheap engine oil in it run it for a bit, cycling the hydraulics then dump that out and see how milky that comes out. Just my opinion and thoughts, others will differ, no problems each to their own.
Here are pics of the cap on the transmission. It calls for 90w in summer and 80w in winter.
I'll check with him tomorrow and see if he has some old oil. He had 5 gallon cans of 10w30 and some hydraulic oil.
 

Attachments

  • 20261119_175804.jpg
    20261119_175804.jpg
    1.6 MB · Views: 0
  • 20261119_175731.jpg
    20261119_175731.jpg
    1.7 MB · Views: 0
That vintage used mineral oil, which is not the same as current gear oils. Weight is about the same, additives are different. There is no W after the weights on that cap. Some are running UTHF in these units now.

Again, what model is the tractor? In 1957 Massey Ferguson, Massey Harris, and Ferguson had some shared models, as the three were one at that time.

As I said if he has been running 85W/90 in it right along, that is his choice. I am just relaying what I see in a Massey Ferguson Operator's manual of that vintage.
 
Massey Harris and Ferguson were together at that point. Just to be clear, a TO 35 is a Ferguson model, not a Massey Harris or Massey Ferguson model. Ferguson had and sold their models and Massey Harris had their own models. Then when the Massey Ferguson joined, another was added. In some cases, the same tractor was sold under three different model numbers, one for each entity.

The Ferguson TO 35 Operator's Manual calls for straight mineral gear oil. SAE 90 above 50 degrees and SAE 8 below 50 degrees. His choice on what he chooses to run; gear oil, mineral oil, or UTHF.

The manual shows two drain plugs, one on the left side about straight down from the pitman arm on the steering box at the lower side of the transmission case and the second on the underside of the differential case. Did you drain both?

Here is a link to a Ferguson TO 35 Operator's manual, if you want for reference.

Ferguson TO 35 Operator's manual

Cheap engine oil is a better way to flush the housings in my opinion. In fact, some of the earlier Ferguson manuals allowed SAE 50 engine oil as a sub for the 90 and SAE 40 for the 80.

The number before the W is actually to signify the oils viscosity at low temperatures. No W is the oil's viscosity at higher operating temperatures.
 
What I do if you can let tractor sit for a a couple of weeks at least I would fill with new oil and mix thourghly. Let tractor sit for at least 2 weeks. Then crack the drain and watch water drip out. Water separates given time and goes to bottom.
 
Sorry. Yes it just says 80 or 90. I added the "w" for 80 or 90 weight.
Tractor is a TO35 and it's a Massey Harris Ferguson.
just for future info (doesn't help the current question) the "W" in a viscosity spec does not stnd for "weight" it is the cold viscosity measurre - the "winter" weight.
 
Crazy as it might sound, one potential for removing water is draining and refilling the cases with a standard mineral (petroleum) oil, and adding an ethanol or isopropyl alcohol to that oil. Those types of alcohols have an affinity for water, and are also solvents for mineral oils, while not being anywhere near as corrosive as methanol (denatured alcohol). That can help suspend the water, emulsify it in the mineral oil, and allow it to drain out on a subsequent drain and refill. If will make the oil yellow-ish again if there is moisture present, but keep it suspended for draining.

Another method is get the gear case warm enough to evaporate the moisture, but the temperatures necessary to de-emulsify the oil/water mixture (usually around 200°F) could be detrimental to other gear case parts and seals.
 
If he saved the old oil, let it set for a while. The water will separate. Once it does, put the old oil back in and do the same with the new oil. It will separate quicker in a warm environment.
 
ranger oil2.jpg

Checked the oil in the Ranger before firing it after it had been sitting for a while. My theory is that the extremely wet Spring caused a ton of condensation in the crankcase. Thank God I always check oil before firing it up.

ranger oil5.jpg

Refilled crankcase, and just drained it.

ranger oil7.jpg

Refilled crankcase again, and ran the motor until it got hot. I believe I did 2 oil changes that were run till hot to get to here. So, that was about 3 different oil changes. The final fill after all water was out, brought total oil changes to 4 IIRC.

ranger oil9.jpg

It was the hot run in that really did the trick AFTER GETTING THE BADLY CONTAMINATED OIL OUT. Motor still runs good, no smoke, or noise. I got very lucky on this one.

I think Watthour has stated the best alternative for the tractor transmission. Alcohol will emulsify water.........it's one of the reasons that Ethanol Blend Gas sorta sucks. It will reach a saturation point, then stratify...............leaving a ton of water on the bottom layer. But meanwhile, the water that's emulsified will crap up your fuel system.
 
water3.jpg

water5.jpg

water6.jpg

water7.jpg


Regular, Non Ethanol, can be a devil too. But..........the water will stay at the bottom of the tank.........not stay suspended in the gas. So, you don't get the fuel system damaged caused by Ethanol.

Same welder............................... I pressurized the tank, and pushed gas out until it had most of the water out, then ran it for a few hours. No problems.

water4.jpg

Just plug your opening with a rag, and put the air to it. The rag lets enough pressure to bypass that it won't ruin the tank. You should never really put more than 5psi to a tank. I use the same method to prime an injector pump on my tractors.
 
Ferguson manuals allowed SAE 50 engine oil as a sub for the 90 and SAE 40 for the 80.
The old Roadranger transmissions spec'd 50W motor oil. They had a filtered oil system. The detergent in the motor oil allows particles to suspend in the oil so that the filter can remove it.
 
The old Roadranger transmissions spec'd 50W motor oil. They had a filtered oil system. The detergent in the motor oil allows particles to suspend in the oil so that the filter can remove it.
So, what exactly does the Road Ranger spec have to do with a Ferguson system, besides adding some more unneeded confusion here?
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top