(800) 853-2651
SHOP NOW

Recent content by 1070PULLER

Yesterday's Tractor Forums
  1. 1

    504 heads

    mel where are you from.im an western ny about 20 miles from erie pa.will be looking to jump up a class and curious as to what these heads might cost and where to find them.thanks.
  2. 1

    504 heads

    just pulled the headsoff of my 504 engine in my puller.notuced that all heads were cracked between valves and injector hole.is this common?is this going to be a problem?was going to have heads ported dont know if i should use these or get different heads.thanks for any help. ps heads are from...
  3. 1

    930/970 case with 504?

    504 will bolt in with very little modifaction on a 930.need to make a throttle linkage crossover and drill a hole for the steering shaft.no mods needed to go into a 970.fran
  4. 1

    Help needed Farmall 95

    if this is a jx 95 tractor thr banjo fitting on the inlet side of the fuel filter will get plugged with debris from time to time.it is usually insects.remove fitting from line clean and you're ready to go.good luck fran
  5. 1

    Ford F350 diesel not starting

    check the valve cover gasket at the plug connection.as they are prone to burningout once in awhile.
  6. 1

    300 case engine

    you can use parts from a 165 massey as the pumps are the same.rebuild kits are readily available and you will find that the pump will perform much bettet.
  7. 1

    head gasket

    bore is now 4.125.thanks
  8. 1

    head gasket

    need a head gasket for an sc case.problem is the bore size is huch larger.any ideas on where to get one close to western,ny.about how much will one cost.thanks
  9. 1

    1135 with engine oil in fuel filters

    engine started surging.pulled plug on secondary filter.engine oil came out.removed filter secondary was pure engine oil primary was mixed.it apears to be pushing oil back through the fuel system.
  10. 1

    801 case diesel

    have never done it but believe they will work.make sure your sleeves are not pittedand there should be room to bore to that size.compression height on pistons is the same.fran
  11. 1

    1135 with engine oil in fuel filters

    hello,have a1135 massey with engine oil getting into the fuel filters.any ideas.it must be coming from the drive for injection pump,but why?any help is greatly appreciated,fran
  12. 1

    Arias Pistons

    need a set at4 and 9/16 for a 44 massey about how much?
  13. 1

    vac rear tires.

    anybody know what the biggest rear tire size was you could get a vac with.28"rims.thanks fran
  14. 1

    wd45 hand clutch

    hi,new to allis got a 45 hand clitch slips;removed cover and there are no shims left to adjust.where can i get new clutch discs?thanks for any help.fran
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top